3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Frontlader — Zweiteiliges Retro-Konsolengehäuse
Frontlader ist ein breites, keilförmiges Konsolengehäuse im Stil der klassischen Frontlader-Konsolen, aufgeteilt in Unterteil und Oberteil zum Verschrauben mit M3. Dunkle Einsätze für Cartridge-Abdeckung, Frontblende und Tasten setzen sich vom hellgrauen Gehäuse ab. Features Unterteil mit Boden, Wänden und vier Schraubsäulen Durchgehende 3,4-mm-Löcher von unten bis zur Trennfuge Oberteil mit Schraubdomen und 2,7-mm-Pilotlöchern Zwei USB-A-Öffnungen in der Front Lüftungsschlitze an Seiten und Oberseite Zwei einzeln druckbare Tasten Dimensions 254 × 203 × 76 mm Trennfuge bei Z 30
GripTurn — M12x1.25 Knurled Cap
Ova zaštitna kapa donosi jednostavno, pouzdano zatvaranje za svaki M12x1.25 navoj. Dizajnirana s urezanim rebrima po cijelom vanjskom opsegu, omogućuje čvrst hvat i lagano ručno zatezanje, dok precizan profil čuva navoj od prljavštine i oštećenja. Gornja strana zatvara kapu, a mali otvor služi za provlačenje konca, sajle ili ventilaciju. Specifikacije Navoj: M12 × 1.25 (unutarnji, dubina 20 mm) Vanjske dimenzije: Promjer 20 mm, visina 22 mm Gornji otvor: Promjer 2.8 mm Površina: Rebrasta za lakše okretanje prstima
RC Car Bevel Gear Rear Drive
A rear-axle drive for an RC car where the motor shaft has to turn 90° into a cross-car axle without the gears skipping or the motor shifting. This set uses a 12-tooth pinion and 24-tooth crown gear (2:1) on a 103.9 mm × 6 mm axle, with an open motor cradle instead of a closed box. Key numbers Gears: module 1.5, 20° pressure angle, 4 mm face width, 90° shaft angle Pitch cone angles: 26.57° (pinion) and 63.43° (crown); cone distance about 20.1 mm Pinion bore 2.1 mm, crown bore 6.2 mm, both with M3 set-screw holes in the hubs Axle supports: 6.4 mm through-hole plus a 17.3 mm seat for 606 bearings (6×17×6) Base: 84 × 92 × 5 mm, M3 holes (3.4 mm clearance); cradle slots allow forward and back adjustment Motor cradle parameters at the top of the file: mw, mh, wall, saddlel, saddley. Measure the real motor and edit them Cover is open at the bottom, with two M3 ears at the rear Printing Print gears with the hub facing up or down on the bed; PETG or nylon preferred Cover prints open-side up without supports Axle is a separate 6 mm steel rod; M3 screws hold supports, cradle, straps and cover
Empreinte Éventail Rayonnant 50mm
Matrice d'empreinte rigide reproduisant la géométrie d'un éventail ouvert. Conçue pour marquer l'argile, la cire ou d'autres pâtes malléables, la pièce est construite sur un plan de référence plat garantissant une pression uniforme. Le motif est généré par un réseau radial de nervures profilées, sans contre-dépouilles, pour assurer un retrait propre du matériau embouti. Dimensions hors-tout : Hauteur de 50 mm, ouverture de 140 degrés. Épaisseur de base : 3 mm (socle rigide). Motif : 13 nervures coniques s'évasant vers l'extérieur, arrêtées 2 mm avant la bordure pour garantir une marge nette. Démoulage : Les arêtes extérieures sont adoucies et les nervures présentent un profil elliptique aplati (mise en dépouille) évitant l'arrachement de la matière. Tirage : Aucun support requis, fond parfaitement plat adapté au plateau de l'imprimante.
Interlocking Socket Organizer Board
Ein Organizer für Stecknüsse rutscht in der Schublade meist hin und her oder passt im Ganzen nicht auf das Druckerbett. Dieses Board bringt Ordnung in ein sehr umfangreiches Nuss-Sortiment (1/4", 3/8", 1/2" und E-Profil) und teilt sich nahtlos auf, um problemlos gedruckt zu werden. Druck und Montage Drei Teile: Das Board ist über Puzzle-Verbinder mit 0.25 mm Toleranz in drei Stücke à maximal 187 mm geteilt. Farbwechsel: Platte und Zapfen bleiben in der Datei als separate Teile deklariert, ideal für einen Farbwechsel beim Drucken (z. B. auf Z=3 mm). Kein Kleben: Die Teile rasten sauber ineinander ein. Sitzt ein Zapfen genau auf der Schnittkante, wird er mitgetrennt und die Nuss überbrückt später beim Aufstecken den Spalt.
Fantasy Chess King, Witch, Fire Horse
Three chunky fantasy chess pieces that tip over easily when the base is narrow: a king, a witch queen and a fire horse, each on a wide 34 mm round base. Key numbers Pieces: king with horned monster face and crowned scepter, witch queen with bent hat and potion bottle, fire horse with flame mane and tail Base: 34 mm diameter, 4 mm thick, flat side down Height: about 55–65 mm per piece Spacing: 45 mm apart in one row, so each can be split off Print: no supports needed for most parts; scepter rod and flame spikes are the thinnest features, so print slowly Colours: gray bodies with black, red and orange details
FLAGE MAROCAINE
A precisely dimensioned 180x120mm base for a Moroccan flag assembly. The model features an accurate 1mm-deep recess carved as five intersecting straight lines, capturing the true geometry of the traditional interlaced pentagram. Through-holes at the five intersecting tips provide exact alignment for a matching drop-in star, while doubling as push-out points if the star needs to be removed after test-fitting. Specifications Dimensions: 180 mm x 120 mm x 3 mm Recess Depth: 1.0 mm (maintains a 2 mm solid floor) Alignment: Five 2.4 mm diameter positioning through-holes Print Settings: Prints flat on its back; no supports required
iPad Picture Frame Adapter Rödlam 21x30
A two-part adapter plate that centers a 5th Generation iPad (9.7") inside an IKEA RÖDALM frame. It acts as a solid backing spacer, locking the tablet into the frame body while providing a cutout exactly the size of the active screen. The split design fits on a standard 220mm print bed and joins with simple flat printed tabs, avoiding overhangs entirely. Remixing and Adjustments Screen Cutout: Currently set to 197 × 148 mm. If you swap to an iPad with a different bezel ratio, you can adjust these dimensions to crop it cleanly. Frame Depth: The total block depth is 30 mm. Thinner frames will require cutting down the outer block height. Cable Routing: A 16 × 25 mm rear channel provides plenty of clearance for bulky aftermarket Lightning cables. Joints: Uses simple 11 × 14 mm rectangular biscuits. You can easily scale these or add more pairs for extra rigidity depending on your printer's tolerances.
Botanical Propagation Tray
A shallow, rectangular nursery tray built specifically for sowing seeds and propagating small cuttings. It is elevated on four short feet to allow excess water to escape underneath, preventing root rot. Design Features Drainage Grid: A regular pattern of 3.5mm holes across the bottom ensures proper water flow. Elevated Base: 5mm feet keep the tray off flat surfaces, allowing air circulation and drainage. Sturdy Walls: 2mm thick perimeter walls provide enough rigidity to move the tray when fully loaded with damp soil.
GlideTrak — Under-Shelf Stemware Rack
GlideTrak is an under-shelf stemware storage block designed to securely hold up to four standard wine glasses upside down by their stems. The dual-channel architecture features a continuous track that flares wide at the opening, allowing smooth, one-handed retrieval and stowing of glasses without requiring precise visual alignment. Engineered as a robust mounting block, it secures flush against the underside of a cabinet while maintaining a clean profile. Features Flared Entry: The stem slot narrows from a 14 mm flared opening down to a 9 mm continuous track, guiding standard stems seamlessly into place. Concealed Mounting: Six countersunk holes with screwdriver access tunnels provide secure upward mounting, hiding the screw heads deep within the block. Support-Free Printing: Engineered to be printed standing vertically on its flat back wall, allowing the internal cavities to form cleanly without the need for support material. Dimensions Overall Footprint: 212 mm wide × 170 mm deep × 22 mm thick. Base Clearance: 82 mm wide internal cavity per channel to accommodate standard glass bases. Stem Track: 9 mm track width, expanding to a 14 mm flare at the front entry.
Freelance Lego fitting cab with Headlight Studs
Brute is a hollow, LEGO-compatible cab modelled loosely on the British Class 47 locomotive. It is six studs wide and four deep, with a closed floor that carries a grid of sockets so it presses onto a standard baseplate. Two studs on the nose give a place to clip on headlight pieces. Features Raked twin windscreens and side door windows Flat, smooth roof at five-brick height Two studs on the front face for headlights Lamp recess centred between the headlight studs 6×4 socket grid under the floor Dimensions Width: 47.8 mm Depth: 31.8 mm Height: 48 mm to the roof Headlight studs: 4.8 mm diameter, 8 mm either side of centre Print notes Print upright on the floor plate, or flipped onto the roof for a clean top surface. Hollow underneath and open at the rear.
VakuumRačva — Ojačani Model
VakuumRačva je robustan, ojačan T-profilni razvodnik namenjen za pouzdano povezivanje vakuumskih vodova. Ovaj model poseduje namenski M10 navoj na zadnjem delu koji je sada dodatno stabilizovan konusom protiv pucanja slojeva pri bočnom opterećenju. Specifikacije Glavni navoj: Unutrašnji 1/4" BSP (dubine 15 mm) za prihvat vakumetra. Dodatni navoji: Spoljni M12 (korak 1.25) na debljem kraku i spoljni M10 (korak 1.5) na zadnjem delu. Protok: Unutrašnji kanali obezbeđuju ravnomeran prenos bez suženja (6 mm i 6.2 mm). Ojačanja: Konusne baze ispod svih kritičnih priključaka čuvaju integritet komada. Preporuke za štampu Štampajte od PETG ili ABS materijala zbog mehaničke otpornosti. Manja visina sloja osiguraće da navoji lakše prihvate spojeve.
HELLO Name Sign, 112 x 36 mm
Desk or shelf name sign with raised bold HELLO lettering on a flat rounded-corner base plate. Letters are set in a heavy sans-serif so strokes stay thick enough to print cleanly. Plate: 112 x 36 x 3 mm, rounded corners Letters: 4 mm raised, Archivo Black, 22 mm cap size Print flat, no supports needed Two colour regions: plate and lettering, suited to a filament change at 3 mm Material: PLA or PETG
П-Shape Bracket Profile
A custom rectangular П-shaped bracket or profile section. Overall dimensions: 29mm wide, 37mm deep, 111mm high Wall thickness: 3mm continuous on top and sides Open base and through-cut depth
Helix — Open-Frame Twisted Fin Lamp Shade
Helix is a flared lamp shade with no solid wall. 72 thin fins spiral through a 60° twist as the shade widens from the base to the top, and three low reinforcing rings hold the whole frame together. The result reads like a lantern or woven cage, and the light comes through as spiralling slats of shadow. The fins and rings are matched on purpose: each fin reaches inward only as far as the rings do, so the inner edge stays clean from bottom to top. A small spoked fitter ring at the base seats the shade over a lamp holder. Dimensions Height: 130 mm Base diameter: about 90 mm Top diameter: about 140 mm Twist: 60° over the full height Features 72 twisted, flared fins, 1.2 mm thick Three low-profile rings at the bottom, middle and top, 3.5 mm tall Fin depth matched to the ring depth (about 6.6 mm at the base, scaling with the flare) Spoked fitter ring at the base, 3 mm tall Print notes Print upright with the fitter ring on the plate. Slow speeds help, since the fins are thin. Use a cool LED bulb only. Fit to a specific socket is untested, so check the fitter ring against your holder.
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
125mm 8-Rib Filter Wrench
Two-piece water filter wrench sized for 125mm (4.5-inch) housings, featuring an 8-rib engagement ring. Joint: Heavy Z-axis sliding dovetail Fit: 125mm inner diameter with 8 notches Print Volume: Parts separated to fit 180x180mm print beds
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
Lazy-Tongs Piano Bottle Caddy
A pantograph-style drink arm in the spirit of a vintage lazy-tongs: a hooked clip straddles the top of a piano's music desk, and a three-unit scissor mechanism unfolds backward to carry a bottle cup. The cup sits inside a wide, rimmed drip tray, so condensation stays off the keys and cabinet. The arm folds flat for storage and stretches out for use. Pivots are print-in-place pins, and the two end joints ride in slots so the arms can open and close. Design notes Cup bore is 76 mm, sized for a standard 33.8 fl oz (1 L) water bottle; cup wall is 85 mm tall. Drip tray is 96 mm across with a 12 mm rim and sits flush with the arm plane. Clip slot fits a music desk about 13 mm thick; adjust the thickness value to suit your piano. Three colored regions: desk clip, scissor arms, cup and tray. Shown in a partly extended pose; the opening angle can be changed to show it folded or fully reached. Best printed as shown, with 0.4 mm clearances at the pivots. Support is only needed under the clip hook. A full bottle is a cantilever load, so keep the arm short for heavier bottles.
110x80mm Invertible Wall Shelf
A simple, sturdy wall shelf with a subtle rim on the underside, designed so it can be mounted inverted. Features a 110x80mm flat area and integrated reinforcement gussets for rigidity against the wall. Dimensions: 110mm width x 80mm depth. Mounting: Twin countersunk screw holes on the backplate. Features: 3mm retention lip and dual structural gussets.
Twin-Chamber Skull Death Whistle
A skull-shaped death whistle with two resonant chambers for a rough, beating scream. Blow into the mouthpiece at the back; air runs along a flat duct, splits on a sharp edge over the window, and sounds both chambers. Remix hooks Duct height (2.4 mm): the main pitch and breathiness control. Try 2.0–3.0 mm. Chamber diameters (20 mm and 12 mm): the gap between them sets how harsh the scream is. Closer sizes give a beat, wider gaps a growl. Chamber height (13 mm): taller means lower pitch. Skull shape: cranium radius is 27 mm, jaw block 34 × 40 × 14 mm. Eye sockets, nose and teeth grooves are separate cuts and easy to restyle. Pairs with: a cord through a drilled lug, or a third chamber behind the first. Overall size is roughly 54 × 78 × 49 mm including the 16 mm mouthpiece. Print upright; the window opens through the crown.
Emergency Stop collar
A high-visibility collar for an emergency stop button. The lettering is set in heavy sans-serif and extruded for clear tactile and visual feedback, making it ideal for multi-color filament swaps. Dimensions Outer Diameter: 64 mm Bore: 25 mm Base Thickness: 2 mm Total Height: 3.5 mm (including text) Print Notes Color Swap: Pause at 2.0 mm (or Z=2.2 mm depending on layer height) to swap to an accent color for the text. Line Width: A 0.4 mm nozzle will handle the bold Archivo Black lettering nicely.
TurnAssist — T-Bar Key Grip
Introducing TurnAssist, a heavy-duty T-bar grip engineered to bring real leverage to stiff locks. Designed specifically for individuals dealing with weak or arthritic hands, it transforms a standard house key into a robust, easy-to-grasp handle. The key secures firmly into the 3mm slot using a standard 1.75mm filament snippet as a locking pin. Features High-Torque Geometry: Configured to be printed flat on the build plate. This aligns the layer lines perpendicular to the turning force, ensuring the handle won't shear under pressure. Flush Pin Clamping: The locking pin passage is counterbored. Filament only needs to be threaded through the center, and snipped ends stay fully recessed to prevent scratching. Accessible Profile: The 60mm wide, 20mm thick crossbar provides a comfortable and secure resting surface for the palm and fingers.
Vented 50mm Speaker Basket
A custom 3D-printable 50mm speaker basket designed for custom driver assemblies. It provides a rigid framework linking a standard 50mm top surround ring to a tailored bottom magnet housing. This version features a completely hollow core: Pass-Through Bottom: The central pole has been deleted and the floor bored out to 25mm, allowing full clearance for a voice coil and T-yoke assembly. Magnet Seat: Leaves a 3mm resting lip for a standard 31mm ring magnet. Acoustic Venting: Four structural struts anchor the assembly while maximizing rear airflow.
Need a part that doesn't exist yet?
Start building →