10-Slot Pill Bottle Organizer
Created today
Description
What it's for
A multi-compartment organizational tray specifically sized for standard pill bottles, arranged in a 2x5 grid. Designed to keep bottles upright and securely separated.
Dimensions
- Compartments: 10 slots, each 1.5 × 1.5 inches (38.1 × 38.1 mm).
- Height: 2 inches (50.8 mm) deep to prevent tipping.
- Overall footprint: ~8.0 × 3.2 inches (202.5 × 82.2 mm).
Print notes
- Standard 2 mm outer walls and internal dividers provide solid rigidity.
- Prints flat on its base. No supports required.
- Inner corners feature a slight 2 mm radius to make retrieving bottles easier.
Images
More like this
Explore more in Storage & Organization →
Asymmetric 16-Slot Makeup Organizer
A single-piece makeup and vanity organizer built to the specified 200x140x90mm volume. The layout uses an asymmetric stepped profile to match compartment depths to their contents while maintaining a clean, minimalist silhouette. All interior vertical edges feature a 3mm radius to prevent powder buildup, and the outer shell carries an 8mm continuous radius. Specifications Dimensions: 200mm (W) × 140mm (D) × 90mm (H) overall. Brush Storage: Two rear compartments (90mm deep) sized for long-handled tools. Creams & Perfume: Twin mid-tier compartments (60mm deep) accommodating standard jars and bottles. Lipstick Grid: 16 independent 21.5mm square slots arranged in a 4×4 matrix (45mm deep). Jewelry Tray: Shallow front-left basin (30mm deep) for rings and small items. Printability: 2.4mm uniform wall and floor thickness. Prints flat without supports.
Split 13-Inch Slip Box
A simple, cleanly split rectangular enclosure meeting a 3" × 1" × 13" outer footprint. Designed to print standing vertically on the build plate, the two halves meet in the middle with a sliding half-lap joint that handles alignment and friction. Remix Hooks The source relies on a few key parameters that dictate the fit and feel. If you pull this into a remix, check these first: Dimensions: Currently W = 76.2, D = 25.4, and L = 172.6 (for each half, achieving the 330.2mm total length). Tweak these to fit whatever board or gear you are housing. Wall: Set to 3mm. This gives enough meat for the half-lap cut (leaving 1.5mm walls at the joint) without feeling overly bulky. Clearance: The joint runs a comfortable 0.4mm tolerance. Tighten it to 0.2mm if your printer is dialed in and you want a semi-permanent friction fit, or loosen it if it binds. Lip Length: The 15mm overlap keeps the assembled box rigid, but dropping it to 8-10mm would save a bit of plastic if the contents don't flex.
13-Inch Magnetic Sliding Box
What it's for A minimalist 13-inch sliding box with an ultra-flush interior (3.5" wide by 1" deep) and heavily magnetized slip joints. Designed for vertical printing without supports, this two-part closure uses eight 5x2 mm magnets hidden inside the 6 mm thick walls of the step-joint, creating a completely smooth interior cavity once assembled. Dimensions Interior: 88.9 × 25.4 × 330.2 mm (3.5 × 1 × 13 inches) Exterior Shell Walls: 6 mm thick Base Ends: 3 mm thick Magnet Sockets: Sized for 5x2 mm disc magnets (5.2 mm diameter x 2.3 mm deep) Print notes No supports needed. The halves print upright on their closed ends. 0.2 mm clearance is built into the male slip joint for a smooth glide up until the magnets catch. Add a small dab of superglue to the magnet pockets before pressing them in.
Wide Friction Slip Box
A 3-inch box is useless when the board you need to house is exactly three and a half inches wide, and a standard slip-joint rattles loose the second it goes into a bag. This version stretches the outer footprint to 3.5 inches to clear the hardware, and packs an extra millimeter of width onto the male tongue to bite into the female half and hold. Width: 3.5" (88.9mm) outer footprint. Fit: The male lip is offset an extra +1mm in width for a tighter friction lock. Print: Prints vertically on the flat bases, no supports needed.
Large Cable Organizer Box
A high-capacity cable management box with a fitted drop-in lid, sized to house bulky power strips, large transformers, and excess cable coils. The rear panel features two mouse-hole style arch cutouts seated flush with the interior floor for easy drop-in cable routing without requiring cables to be threaded through tight slots. What it's for Concealing power strips, power bricks, and cable runs on desktops or floors Floor-level cable pass-through that keeps cords flat against the surface Dust protection with an easy-access lift-off lid Dimensions Internal Clearance: 215.9 mm (8.5") W × 292.1 mm (11.5") D × 127.0 mm (5.0") H Wall Thickness: 3.0 mm Port Size: 40 mm wide × 64 mm high arched openings flush to the floor plate Outer Footprint: 221.9 mm × 298.1 mm × 133.0 mm (excluding lid hover offset) Print notes Print the box base-down with no supports needed for the arched ports. The lid prints flat on its top face for maximum surface quality and bed adhesion. Requires a build volume of at least 300 mm × 225 mm.
Trinket Box With Captive Hinge
Most 3D-printed boxes rely on thin plastic living hinges that fatigue and snap off after a week of use, or require separate filament fragments as pins that eventually back out. This print-in-place trinket box uses a five-knuckle mechanical barrel hinge with integrated teardrop pins to prevent bridging collapse. A front thumb-tab with an offset detent provides a positive snap closure so the lid doesn't flap open when jostled in a drawer. Dimensions: 70 mm x 50 mm x 30 mm overall footprint. Walls: 2 mm solid perimeters for rigidity. Tolerances: 0.4 mm clearance inside the hinge barrel to prevent the knuckles from fusing during extrusion. Printing: Print fully closed, flat on the base. Requires no supports.