3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
Soporte de tarjetas con estrella grabada
Bloque rectangular con una ranura central para tarjetas y una estrella de cuatro puntas con lados curvos, grabada hacia el interior de la cara frontal. Bloque de 115 x 25 x 20 mm con bordes achaflanados Ranura de 4 mm de ancho y 10 mm de profundidad, de extremo a extremo Estrella curva de 16 mm de punta a punta, hundida 1,5 mm y centrada en la cara frontal Se imprime sin soportes apoyada sobre su base
Hexagonal Honeycomb Floating Shelf Set
A three-cell honeycomb of hexagonal wall shelves, each cell deep enough for small plants or a few books. The cells share walls and mount as one cluster, so a blank wall becomes a single graphic statement. Two keyhole slots per hex are hidden in the back panel, so no brackets are visible once hung. What it's for Displaying small potted plants, books, or ornaments on a wall. Turning a plain wall into a honeycomb feature without visible hardware. Hanging flush: screw heads sit in recesses on the wall side of the 6 mm back panel. Dimensions Each hex: 200 mm across the points, about 173 mm across the flats. Depth: 100 mm per shelf. Back panel: 6 mm thick. Side wall: 5 mm. Keyholes: two per hex, 80 mm apart, cut through the back panel with a recess on the wall side. Layout: three hexes joined along shared walls in a triangular cluster. Print notes The cluster is oriented back-down on the build plate, so it needs no supports. It prints as one large fused piece. Check that it fits your bed, or split it into single hexes. Use screws with heads that fit the keyhole recess, and anchors suited to your wall type. Remix ideas Add more cells to extend the honeycomb sideways or upward. Change the depth for shallow trinket shelves or deeper book cubbies. Print each hex separately in different colours and assemble them on the wall. Add a lip or a drainage hole for planters.
Fireplace Advent Calendar, Printable Multi-Piece
What it's for A 24-day advent calendar styled as a brick chimney on a fireplace. Pull a day's divider and the prize drops down the flue into the firebox. Santa is stuck at the top. Dimensions Two chimney sections, split at 204 mm 12 levels with 2 compartments each, 20 mm clear height 24 flat dividers and a separate Santa Removable firebox filler, 60 mm wide, with pull tab and break-away nubs. It leaves open gaps at the sides and clears the firewood. Remix ideas Change the garland to lights or holly Add a name or year to the mantel Resize the compartments for larger prizes
Wickiup — Domed Hut Miniature
Wickiup is a small domed hut miniature inspired by the Apache wickiup shown in the linked reference image. A hollow dome with an arched doorway and a roof smoke hole, wrapped in raised bands that suggest woven thatch. Features Hollow dome, about 60 mm wide and 30 mm tall Arched doorway facing the front Smoke hole at the top Raised thatch bands in a second colour Print notes Flat base, so it prints without a raft Door arch is small; supports are rarely needed
wigwam
Scale model of a wigwam-style domed hut on an 88 mm round base, with an arched front doorway, a top smoke hole, three binding bands and hay thatch strands angled down the dome. Fit and dimensions Base disc: 88 mm diameter, 2 mm thick Dome: about 80 mm wide, roughly 32 mm tall overall Doorway faces -Y; thatch is left clear of it Check before printing Hay strands are about 1 mm thick. Use a 0.4 mm nozzle and expect fine, fragile detail. Not a functional enclosure, and not scaled to fit any figure or miniature line.
model saat
A slim protective sleeve for the SIBIONICS SiWatch with its own reinforced strap lugs, so strap load bypasses the broken originals. The screen, back sensors and charging contacts stay open, and two separate button openings sit on one side edge. Remix hooks button1offset / button2offset: Y position of each opening along the side, measured from the watch centre. Starting values are -5 mm and +5 mm. Each moves independently. btnz, btnlen, btn_h: opening height above the back (5.5 mm), length (6 mm) and height (3.5 mm). btn_side: 1 for the +X edge, -1 for -X. Cavity: watchw 38, watchl 44, watchh 11 and cornerr 9 mm are placeholders to measure. Strap: strapw 22, bard 3, barz 6.5 and bary 1.5 mm. Pairs well with a test-fit print in cheap filament before the final one.
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
ESP32 Enclosure with 1.3 Inch OLED Lid
Two-piece enclosure for a 30-pin ESP32-WROOM-32 DevKit V1 with a 1.3 inch SH1106 OLED mounted in the lid. Shown exploded with heat inserts and M3 screws aligned to the corner holes. The lid has a 35.5 x 34.5 mm recess on the underside that holds the OLED PCB, and a 35.5 x 20.5 mm window through the front panel for the visible display area. ESP32 pocket: 52 x 28 mm, 14 mm deep Outer size: about 56.8 x 40.4 mm, 2.4 mm walls Front USB-C slot, 10 x 4 mm Four corner screw holes for M3 screws and heat inserts Front panel thickness behind the window: 1.6 mm Print the lid face-down for a clean front surface.
Veranda Back Railing Bays
Railing section for the back half of the veranda, made to print separately from the deck base. It covers the long left side and the short end, with pickets running between a lower and a top rail. Left side bay with end post, plus the end-span railing across the back Pickets about every 110 mm at full scale Posts sit flat on the deck surface for gluing Same scale and position as the deck base, so the pieces line up
Magic octagon coin.
An octagon coin whose raised arrow disappears into the bed side: the underside is now flat with the arrow cut in as a shallow dent, so no layer prints over empty air. Size: 50 mm across corners, 3 mm body, 4.2 mm total height. Top: 0.6 mm raised rim, with the arrow rising 1.2 mm so it stands 0.6 mm above the rim. Change filament at that layer to colour only the arrow. Underside: flat, with a 0.6 mm deep arrow indentation turned 90° from the top arrow, plus a 1.4 mm wide, 0.6 mm deep groove about 2 mm in from the edge. Print: lie it flat, underside on the bed, no supports.
Schlüsselanhänger paula
Schlüsselanhänger mit Namen Paula, bei dem die Schrift nicht flach untergeht: Sie steht 0,5 mm erhaben auf der Platte und lässt sich mit dem Finger ertasten. Das Kettenloch sitzt seitlich, damit der Ring nicht über die Buchstaben schleift. Platte: 30 × 14 × 2 mm, Ecken mit 3 mm abgerundet Schrift: „Paula“ in Lobster, 0,5 mm erhaben Kettenloch: 3,5 mm Durchmesser, linke Seite Druck: flach auf der Platte, ohne Stützen, 0,2 mm Schichthöhe empfohlen
Bulkhead Signal Box with RJ45 and SMA
A compact 130 × 65 × 35 mm enclosure in the spirit of a field-radio interface box: Ethernet in one end, antenna and cable gland out the other. The lid sits flush and is held by four M2.5 × 10 mm countersunk screws threading into corner posts. RJ45 end: 16.5 × 14 mm rectangular opening, centred in width and height. Other end: 6.5 mm hole for a through-mount SMA connector and a 12.5 mm hole for a PG7-style cable gland, spaced evenly across the 65 mm width and centred in height. Walls: 2.5 mm; lid 3 mm, printed flat beside the box. Screws: 2.1 mm pilot holes in the posts for self-tapping M2.5; countersunk clearance holes in the lid.
Bulkhead Signal Box with RJ45 and SMA
A compact 130 × 65 × 35 mm enclosure in the spirit of a field-radio interface box: Ethernet in one end, antenna and cable gland out the other. The lid sits flush and is held by four M2.5 × 10 mm countersunk screws threading into corner posts. RJ45 end: 16.5 × 14 mm rectangular opening, centred in width and height. Other end: 6.5 mm hole for a through-mount SMA connector and a 12.5 mm hole for a PG7-style cable gland, spaced evenly across the 65 mm width and centred in height. Walls: 2.5 mm; lid 3 mm, printed flat beside the box. Screws: 2.1 mm pilot holes in the posts for self-tapping M2.5; countersunk clearance holes in the lid.
Curved Snap-In Interior Trim Cover
A 123 × 180 mm curved interior trim cover with a straight bottom edge, a stepped outline (107 mm wide at the top, 123 mm in the lower 85 mm) and a 3 mm panel. The perimeter flange follows the crowned surface so the part sits flush around the opening. Remix hooks Surface crown: the front curvature is a few millimetres in both directions. Flatten or deepen it to match a measured body profile. Raised area: 10 mm high with a soft ~30 mm blend at the upper left. Change height or width to suit. Clips: five per side at 18, 54, 90, 126 and 162 mm, 14 mm wide and 4.5 mm thick, with a ~2 mm hook. Adjust hook depth to the real metal edge thickness. Rear frame: 15 mm deep, 2.8 mm wall, inset 3.5 mm. Change the inset for a tighter or looser fit. Pairs with: fuzzy skin in the slicer for a textured look. Print in PETG, ASA or ABS.
Y-Rohrstück 75 auf 39 mm mit Steckende
Y-Rohrstück, bei dem ein weiteres Rohr auf dem oberen Ende nicht richtig sitzt, weil kein gerades Stück zum Aufstecken vorhanden ist. Der obere Abschnitt hat jetzt ein 20 mm langes gerades Ende mit 39 mm Außendurchmesser. Unterer Teil: 75 mm Außendurchmesser, 30 mm lang Konus: 30 mm lang, von 75 auf 39 mm Steckende oben: 39 mm Außendurchmesser, 20 mm lang Abzweig: 39 mm Außendurchmesser, 48° zur Rohrachse, schneidet die obere Öffnung nicht Wandstärke: 2 mm überall Druck: aufrecht auf der 75-mm-Öffnung, der Abzweig braucht Stützen
Black and Gold Wedge Desk Nameplate
A wide desk nameplate with a black rounded base, thin gold border and raised gold lettering. The name sits on the top line in large capitals, with ASSISTANT PROFESSOR centred below it in smaller capitals. The plate is tilted back on an integrated wedge stand, so it needs no separate parts. The back and underside are flat, and the build needs no supports. Text: SIMRANJEET KAUR LOHAT (top), ASSISTANT PROFESSOR (bottom) Colours: black base and wedge, gold border and letters Letters raised 2 mm, border raised 1.2 mm Plate size 200 × 64 mm, tilted back 15° from vertical Suited to multicolour printing with a 0.4 mm nozzle
Flat Ground Plate 45x42x2 mm with Tabs
Flat 45 × 42 × 2 mm ground plate with two side tabs on the front 45 mm edge and two small blocks on the back edge. Overall width across the tabs is 50.4 mm. Plate: 45 × 42 × 2 mm, sharp edges Side tabs: 1.4 mm thick, flush with the underside, 50.4 mm overall span Back blocks: 1.5 mm wide, 1 mm thick, 1.5 mm protrusion, 5 mm from each side edge Print flat, no supports needed
Veil — Air Freshener Front Plate
Veil is a plain, flat front cover for an automatic air freshener dispenser. It is a clean blank with rounded corners, ready to be used as-is or modified with cutouts for a nozzle, sensor or window. Dimensions Height: 230 mm Width: 76 mm Thickness: 1 mm Corner radius: 8 mm Print notes Print flat on the bed, no supports needed. At 1 mm thick, a wide brim or a slow first layer helps prevent warping.
Toy Story Sky Cloud Cookie Cutter
A cookie cutter echoing the wallpaper clouds from Andy's room: a big bump on the upper left, smaller puffs along the top and a long flat base. The centre is open so dough passes straight through. 15 mm tall wall, about 1.2 mm thick, thin clean cutting edge on the flat bottom Widened rim at the top for pressing by hand About 100 mm wide, prints flat with no supports
Advent Calendar Drawer With Grip
A single replacement drawer for an Advent calendar: open-top box, 41.5 × 23.5 × 44 mm, 1.5 mm walls and floor, with the number engraved on the front above a small square grip. Remix hooks Grip size: 8 × 5 mm face, 4 mm projection (5 mm deep body, 1 mm embedded). Make it wider for easier pulling. Grip rounding: 0.8 mm edge rounding. Raise it for a softer look, drop it for a sharper square. Number: 8 mm Roboto, engraved 1 mm deep near the top. Change the digit for other drawers. Fit: trim 0.2 mm off width and height if it binds in the frame. Pairs with: the other numbered drawers, since the front footprint is unchanged.
Wall Shelf, 20 cm Glue-On
A small wall shelf that sits flat against the wall and glues on, with no drilling and no screws that miss the stud. The tall back plate gives the adhesive a big flat face, and two triangular gussets stop the front edge from sagging or peeling off. Key numbers Shelf top: 200 mm long x 80 mm deep x 4 mm thick Back plate: 200 x 40 mm, 4 mm thick, flat on the wall side Two gussets, 4 mm thick, each 34 mm tall Print: shelf upright on its back plate or flat on the top, no supports needed with the plate down; PETG or PLA, 3+ perimeters Glue: construction adhesive or mounting tape on the back plate face
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Dragon Head Blind Cord Cleat
Blind cords slip off a plain cleat the moment the tension changes. This dragon head cord cleat has a tusk on each side of the snout, so the cord wraps under it and stays put. Mounting plate: 30 x 70 mm, 4 mm thick, two countersunk screw holes Tusks: ball-tipped, project about 16 mm out from the centre on each side, above the cord path Cord slot: 3.5 mm tall, runs left to right through the snout Flames: three tongues from each nostril, pointing forward over the plate Extras: horns, brow ridges, cheek spikes Print: plate flat on the bed; the horns and flames are small overhangs, so a little cleanup or supports may help
Need a part that doesn't exist yet?
Start building →