200mm Square 3-Compartment Toolbox
Created 3 months ago
Remixed once
Description
A 200mm square storage box equipped with three equal front-to-back compartments, accompanied by a drop-on lid. The lid has a built-in 0.5mm clearance margin to ensure it slips onto the base easily without jamming, ideal for standard or Hyper PLA printing profiles.
What it's for
Sorting and protecting mid-sized tools, hardware, or craft supplies. The three wide compartments keep items from shuffling around while maintaining a clean, accessible layout.
Dimensions
- Base outer: 200 x 200 x 50 mm
- Lid outer: 205 x 205 x 12 mm
- Compartments: Three slots, each 64 x 196 x 48 mm internally
- Clearance: 0.5 mm all around the lid fit
- Wall thickness: 2 mm universally
Print notes
The base and lid are positioned side-by-side. On a standard 220x220mm print bed, you will need to split the parts in your slicer and run them as two separate print jobs. No supports are required.
Photos
Technical views
More like this
Explore more in Storage & Organization →
Open-Top Square Box 75 × 75 × 25 mm
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
Low-Profile Thread Extractor Tray
A compact drop-in tray for a ten-piece thread extractor set, laid out like a tiny pegboard of hex sockets. Two rows of five hex pockets hold the extractors upright, with a finger slot across each pocket for easy lifting. Design notes Outer size 96 × 42 × 15 mm with 5 mm rounded vertical corners Hex pockets 12.9 mm across the flats, 12 mm deep 3 mm solid floor Sized to sit inside a case or toolbox
Mini 19-Cone Henna Carousel Stand
A compact two-tier henna cone stand: 110 mm trays, 60 mm apart, holding 19 cones tip-down, joined by a 25 mm central column and a screw cap. The top tray's 15 mm holes sit directly over 6 mm tip holes in the lower tray. A foot ring under the lower tray keeps cone tips off the table. Remix hooks Tray spacing: 60 mm now. Raise it for longer cones. Ring layout: 12 holes at 43 mm radius plus 7 at 25 mm radius. Wall between rings is about 3 mm, so adding holes means growing the tray. Tray diameter: 110 mm. Scale it up and add a third ring for more capacity. Hole size: 15 mm top, 6 mm bottom. Adjust to your cone brand. Pairs with: a turntable disc or non-slip mat under the foot ring.
Staggered 5-Key Hook Extender
A tall back plate that hangs from a key rack and holds five keys on alternating left and right pegs, so fobs dangle without touching each other. The plate is 46.2 mm wide, 240 mm tall and 12 mm thick, with a 12 mm hang hole at the top right. Each peg is 8 mm in diameter, runs straight for 12 mm, then curves upward through 75° to keep rings seated. Remix hooks Plate thickness (12 mm): the easiest stiffness lever. Pegs are set into the plate face, so going thicker needs no other changes. Peg spacing (42 mm pitch): raise it for longer fobs, lower it to fit more pegs on a shorter plate. Bend angle (75°) and straight run (12 mm): lengthen the run for larger rings, ease the angle for a flatter peg. Hang hole (12 mm): resize to match your rack hook. Pairs with: any horizontal key rack with a post or screw head that fits the hole.
Caja Compacta para Ender 3
Caja con tapa y orejetas de cierre, ajustada para imprimirse en una cama de 220 × 220 mm como la de la Ender 3 Pro. El cuerpo mide 203 mm de largo y las orejetas ya no sobresalen tanto, así que cada pieza queda en 217 mm de ancho. Detalles Interior de 193 × 95 mm. 4 orejetas con agujero para insertos roscados M6. Tapa con solapa y ranura para junta de goma. Placa vertical con refuerzos. A tener en cuenta Cada pieza se imprime por separado; en el modelo aparecen una al lado de la otra solo para la vista.
Caja 200x95x40 con insertos roscados M6
Caja con tapa para insertos roscados M6 en cuatro orejetas de cierre, con medidas interiores de 200 × 95 × 40 mm y paredes de 5 mm. Qué lleva 4 orejetas exteriores con agujero de 8,4 mm y 8 mm de profundidad para insertos roscados M6 de 9 mm de diámetro exterior. Tapa de 10 mm de grosor con 4 agujeros avellanados de 6,4 mm. Solapa de tapa de 70 × 40 mm, con 10 mm de grosor y esquinas superiores con radio de 15 mm. Lleva un agujero central de 8 mm y otro de 6 mm a 25 mm del centro. Ranura de 1,5 mm en caja y tapa para un cordón de goma de unos 2 mm. Placa vertical de 60 mm con triángulos de refuerzo de 3 mm de grosor. Medida a comprobar El diámetro exterior real de los insertos. El agujero está pensado para 9 mm. No encaja Tornillos distintos de M6 en las orejetas, ni cordones de goma de más de 3 mm.