Asymmetric 16-Slot Makeup Organizer
Created 1 months ago
Description
A single-piece makeup and vanity organizer built to the specified 200x140x90mm volume. The layout uses an asymmetric stepped profile to match compartment depths to their contents while maintaining a clean, minimalist silhouette.
All interior vertical edges feature a 3mm radius to prevent powder buildup, and the outer shell carries an 8mm continuous radius.
Specifications
- Dimensions: 200mm (W) × 140mm (D) × 90mm (H) overall.
- Brush Storage: Two rear compartments (90mm deep) sized for long-handled tools.
- Creams & Perfume: Twin mid-tier compartments (60mm deep) accommodating standard jars and bottles.
- Lipstick Grid: 16 independent 21.5mm square slots arranged in a 4×4 matrix (45mm deep).
- Jewelry Tray: Shallow front-left basin (30mm deep) for rings and small items.
- Printability: 2.4mm uniform wall and floor thickness. Prints flat without supports.
Images
More like this
Explore more in Storage & Organization →
Mini 19-Cone Henna Carousel Stand
A compact two-tier henna cone stand: 110 mm trays, 60 mm apart, holding 19 cones tip-down, joined by a 25 mm central column and a screw cap. The top tray's 15 mm holes sit directly over 6 mm tip holes in the lower tray. A foot ring under the lower tray keeps cone tips off the table. Remix hooks Tray spacing: 60 mm now. Raise it for longer cones. Ring layout: 12 holes at 43 mm radius plus 7 at 25 mm radius. Wall between rings is about 3 mm, so adding holes means growing the tray. Tray diameter: 110 mm. Scale it up and add a third ring for more capacity. Hole size: 15 mm top, 6 mm bottom. Adjust to your cone brand. Pairs with: a turntable disc or non-slip mat under the foot ring.
Staggered 5-Key Hook Extender
A tall back plate that hangs from a key rack and holds five keys on alternating left and right pegs, so fobs dangle without touching each other. The plate is 46.2 mm wide, 240 mm tall and 12 mm thick, with a 12 mm hang hole at the top right. Each peg is 8 mm in diameter, runs straight for 12 mm, then curves upward through 75° to keep rings seated. Remix hooks Plate thickness (12 mm): the easiest stiffness lever. Pegs are set into the plate face, so going thicker needs no other changes. Peg spacing (42 mm pitch): raise it for longer fobs, lower it to fit more pegs on a shorter plate. Bend angle (75°) and straight run (12 mm): lengthen the run for larger rings, ease the angle for a flatter peg. Hang hole (12 mm): resize to match your rack hook. Pairs with: any horizontal key rack with a post or screw head that fits the hole.
Apothecary Grid Hinged Pill Box
A pharmacy-drawer grid in miniature: thirty round wells in a 6×5 layout, topped by a lid that swings open on a real pin hinge at the back edge. The lid prints flat beside the tray and clicks into the hinge ears once a short pin is slid through. 30 slots, 16 mm wide and 14 mm deep Hinge pin hole sized for a 1.75 mm filament offcut, about 56 mm long Front finger tab on the lid for easy opening Lid and tray print without supports in separate pieces
Two-Piece Pro Controller Wall Holder
A 380 mm wall holder for a PS5 and a Switch Pro controller is too wide for most print beds, and a single plate can crack along its length. This version prints as two 190 mm halves that lock together with two butterfly keys. Fit and print Split line: centre of the plate, through the Yu-Gi-Oh! ring emblem Keys: two butterfly-shaped keys, 24 mm wide and 20 mm tall, 2.9 mm thick, printed flat Key pockets: cut 3.3 mm deep into the back face, 0.3 mm clearance all round Assembly: press the keys into the back pockets across the seam, then screw the halves to the wall. The wall holds the keys in Mounting: eight countersunk screw holes in total, four per half Printing: halves lie on their backs or stand on the shelf base. No supports are needed for the hollow blocks Pocket sizes are 166 mm wide and 70 mm deep, from typical controller sizes and not from measurements of a specific controller.
Retró vadászdoboz 16-os sörétes töltényekhez
Csuklós fedelű, ötrekeszes doboz, amely úgy néz ki, mint egy régi vadászfelszerelés darabja: lapos, szögletes test, hátul csuklópánttal nyíló fedél, elöl két zárral, amelyeket kis fogóorr fog meg. Belül öt párhuzamos fészek várja a töltényeket — 21,8 mm széles vájat, 22,6 mm-es osztás, 74 mm hosszú hüvelyekhez. Csukva a doboz 120 × 90 mm-es alapterületű, kényelmesen elfér egy lőszertáskában vagy a szekrény polcán. Ami a nyomtatáshoz tartozik: Öt darab kerül a tálcára: a doboz alsó része, a fedél, a két zár, a négy zárhoz való csavar és a csuklótüske. A csukló egy külön 3 mm-es pálcából áll össze, a zárakat 4 mm-es menetes csavarok rögzítik a fedélhez — a doboz tehát összeszerelést igényel, nem egy darabban készül el. Nyomtatásnál a dobozt és a fedelet a lapos oldalukra érdemes fektetni, a zárakat, csavarokat és a tüskét külön. Illesztés: a fészek mérete becslésen alapul, ezért érdemes egy tölténnyel próbát tenni: peremes hüvelyeknél vagy a 74 mm-nél hosszabb daraboknál a vájatok szűkebbek vagy rövidebbek lehetnek a kelleténél. Egy kis reszelés a fészek falán sokat segít, és a zár csavarját se húzd túl szorosra, hogy a fedél ne feszüljön.
Low-Profile Extractor Set Tray
A slim, flat drop-in tray in the spirit of a toolbox foam insert, with ten hex pockets in two rows of five. Each pocket fits a thread extractor with a 12.8 mm hex base, and a finger slot across each one makes lifting them out easy. Overall size: 96 × 42 × 10 mm Pockets: 13.7 mm across flats, 7 mm deep, 3 mm solid floor Extractors stand upright, so the tall ends project above the tray Rounded vertical corners for easy fit into a case