Created 23 days ago
Description
A snap-in C clip that holds a 22 x 33 mm 9 V battery container. The opening sits in the front long wall, so the container presses in and pulls out when the battery needs changing.
Images

Gavetas e bancadas viram bagunça quando parafusos, cabos e peças pequenas se misturam. Esta caixa organizadora separa tudo em 6 compartimentos fixos, em grade de 3 x 2. Medidas e impressão Tamanho externo: 180 x 120 x 50 mm Paredes e fundo: 2 mm Divisórias: 2 mm, 5 mm mais baixas que a borda Cada compartimento mede cerca de 56 x 57 mm por dentro Imprime sem suportes, com o fundo apoiado na mesa PLA ou PETG, com 0,2 mm de altura de camada
A round 88 mm ornament disc, 4.8 mm thick, with a grid of LEGO-compatible studs on the face and a hanging loop at the top. Printed in red, flat, with no supports. Remix hooks Stud diameter: 5.0 mm now (standard is 4.8 mm). Raise it to 5.05 for a firmer grip, or drop it to 4.9 if bricks sit too tight on your printer. Stud height: 1.8 mm. Taller studs give a deeper grip but need more bridging care. Disc thickness: 4.8 mm, or 1.5 LEGO plates. Use 3.2 mm for one plate or 9.6 mm for a full brick height. Disc diameter: 88 mm on an 8 mm stud pitch. The stud grid is cut to a 37 mm radius, which leaves a plain rim. Loop: 13 mm outer, 5.5 mm hole. Widen it for ribbon. Pairs with: 1x1 and 2x2 bricks, tiles, and small minifigure scenes.
A hexagonal box with a matching lid, printed as two separate pieces. The box is 50 mm tall and 80 mm across the corners, with 2.4 mm walls and a 3 mm floor. The lid is a 3 mm hexagonal plate with a 6 mm hollow lip underneath. The lip sits inside the box opening with about 0.4 mm of clearance per side, so the lid stays put without a tight press fit. Box: 80 mm across corners, 50 mm tall, chamfered base edge Lid: 80 mm across corners, 3 mm plate, 6 mm inner lip Print the lid flat with the lip facing up No supports needed for either piece
Caja estanca para Garmin Montana 710, abierta por arriba, con ventana frontal, ranura de junta, tapa con orejas atornilladas, pestaña trasera con agujero de 6 mm y refuerzos. Interior: 94 x 37 x 192 mm Paredes de 4 mm Saliente frontal superior con dos triángulos laterales Tapa y lámina protectora incluidas
210 mm çapında, 60 mm yüksekliğinde yuvarlak bir saklama kabı. İçi, merkezden duvara 72° aralıkla çıkan beş bölmeyle eşit gözlere ayrılmış; bölmeler dişli boyun bölgesinde de devam ettiği için kapak takılıyken gözeler birbirine karışmaz. Kapak, gövdenin üstündeki dış dişe vidalanır; taşırken kendiliğinden açılmaz. Gövde ve kapak ayrı ayrı basılır. Remix için başlangıç değerleri Gövde: 210 mm çap, 60 mm yükseklik; yan duvar ve taban 1,6 mm, iç bölmeler 1,2 mm Kapak: 210 mm çap, 14,3 mm yükseklik, üst et 2,4 mm; düz yüzü tablaya gelecek şekilde basılır Diş: 12 mm boy, 5 mm adım, 3 ağızlı (hatve 15 mm), 0,5 mm boşluk; kapatmak için yaklaşık 0,8 tur (yaklaşık 290°) Diş çapı 204 mm, boyun iç çapı 197 mm; gövdenin üstündeki basamak her yanda yaklaşık 3 mm kalıyor Nereleri değiştirmek mantıklı Göz sayısı: bölmeler merkezden eşit açıyla çıktığı için sayıyı değiştirmek bölme açılarını da değiştirir; açıyı 72°'den farklı seçersen gözler eşit olmaktan çıkar, bunu bilerek yap. Bölme kalınlığı: 1,2 mm ince ve malzeme dostu; daha ağır parçalar koyacaksan kalınlaştır, ama göz hacmi daralır. Diş boşluğu: 0,5 mm baskıda rahat çalışıyor; makinen sıkı basıyorsa düşür, kapağı sık açıp kapatacaksan artır. Dış çap ve yükseklik: 210 × 60 mm raf ve çekmece için uygun bir başlangıç; aynı dişi koruyup gövdeyi derinleştirmek en kolay varyant. Alt kısımdaki diş dibi duvarı ince kaldığı için o bölgeyi basarken katman ayarlarına dikkat etmek gerekir. Beş gözü sayesinde dökme parçaları, vida ve küçük donanımı ya da atölye malzemesini tek kapta ayrı ayrı tutmak için uygundur; aynı diş ölçüsünü koruyan daha sığ bir gövde ya da daha çok gözlü bir üst katman iyi bir eşleşme olur.
A 380 mm wall holder for a PS5 and a Switch Pro controller is too wide for most print beds, and a single plate can crack along its length. This version prints as two 190 mm halves that lock together with two butterfly keys. Fit and print Split line: centre of the plate, through the Yu-Gi-Oh! ring emblem Keys: two butterfly-shaped keys, 24 mm wide and 20 mm tall, 2.9 mm thick, printed flat Key pockets: cut 3.3 mm deep into the back face, 0.3 mm clearance all round Assembly: press the keys into the back pockets across the seam, then screw the halves to the wall. The wall holds the keys in Mounting: eight countersunk screw holes in total, four per half Printing: halves lie on their backs or stand on the shelf base. No supports are needed for the hollow blocks Pocket sizes are 166 mm wide and 70 mm deep, from typical controller sizes and not from measurements of a specific controller.