Caja Secreta con Llave Clásica
Created 1 months ago
Description
Una caja fuerte impresa en 3D que esconde su apertura a plena vista. En lugar del típico tirador, la tapa se asienta completamente a ras y requiere una llave física estilo tradicional para desenroscarla.
El interior está optimizado con un techo cónico, por lo que imprime limpio sin necesidad de soportes.
Características del montaje
- Impresión sin soportes: La cámara y la rosca se imprimen directo en la base.
- Llave dentada: Perfil plano tipo casa con agujero para llevarla en el llavero.
- Seguridad visual: La tapa a ras evita poder girarla con los dedos.
Images
More like this
Explore more in Storage & Organization →
Arecson — Letrero con Base Rectangular
Letrero con el texto "Arecson Dj" en relieve sobre una base rectangular plana de 2 mm. Pensado como placa o rótulo sencillo para un puesto de DJ, con letras en Montserrat fáciles de leer. Dimensiones Base: 90 × 24 × 2 mm Letras: 4 mm de relieve sobre la base Tipografía: Montserrat, tamaño 13 Notas de impresión Imprime plano, sin soportes. Las letras pueden hacerse de otro color cambiando de filamento en la capa 2 mm.
Mini 19-Cone Henna Carousel Stand
A compact two-tier henna cone stand: 110 mm trays, 60 mm apart, holding 19 cones tip-down, joined by a 25 mm central column and a screw cap. The top tray's 15 mm holes sit directly over 6 mm tip holes in the lower tray. A foot ring under the lower tray keeps cone tips off the table. Remix hooks Tray spacing: 60 mm now. Raise it for longer cones. Ring layout: 12 holes at 43 mm radius plus 7 at 25 mm radius. Wall between rings is about 3 mm, so adding holes means growing the tray. Tray diameter: 110 mm. Scale it up and add a third ring for more capacity. Hole size: 15 mm top, 6 mm bottom. Adjust to your cone brand. Pairs with: a turntable disc or non-slip mat under the foot ring.
Pata telescópica 18 mm, recorrido 5 mm
Conjunto de dos piezas para las esquinas de una caja de controladora DJ: un soporte superior de 18 mm de diámetro que se fija al fondo de la caja y una pata inferior que se desliza dentro con 5 mm de recorrido. Se imprime en PETG, sin muelles, tornillos ni roscas. Especificaciones Soporte superior: Ø18 mm, altura 11 mm, base superior plana de 1,5 mm para pegar. Pata inferior: Ø10 mm de vástago, cabeza Ø11,8 mm, altura 10 mm, base plana para goma antideslizante. Holgura: 0,25 mm por lado (parámetro tol, ajustable según impresora). Guías: 3 nervios interiores que limitan el juego lateral. Retención: anillo tope de 1,5 mm; la cabeza de la pata, con ranuras en cruz, encaja a presión por abajo. Recorrido: 5 mm. Imprimir 4 conjuntos. La pieza superior se imprime con la base plana sobre la cama; la pata con la base hacia abajo.
Two-Piece Pro Controller Wall Holder
A 380 mm wall holder for a PS5 and a Switch Pro controller is too wide for most print beds, and a single plate can crack along its length. This version prints as two 190 mm halves that lock together with two butterfly keys. Fit and print Split line: centre of the plate, through the Yu-Gi-Oh! ring emblem Keys: two butterfly-shaped keys, 24 mm wide and 20 mm tall, 2.9 mm thick, printed flat Key pockets: cut 3.3 mm deep into the back face, 0.3 mm clearance all round Assembly: press the keys into the back pockets across the seam, then screw the halves to the wall. The wall holds the keys in Mounting: eight countersunk screw holes in total, four per half Printing: halves lie on their backs or stand on the shelf base. No supports are needed for the hollow blocks Pocket sizes are 166 mm wide and 70 mm deep, from typical controller sizes and not from measurements of a specific controller.
Staggered 5-Key Hook Extender
A tall back plate that hangs from a key rack and holds five keys on alternating left and right pegs, so fobs dangle without touching each other. The plate is 46.2 mm wide, 240 mm tall and 12 mm thick, with a 12 mm hang hole at the top right. Each peg is 8 mm in diameter, runs straight for 12 mm, then curves upward through 75° to keep rings seated. Remix hooks Plate thickness (12 mm): the easiest stiffness lever. Pegs are set into the plate face, so going thicker needs no other changes. Peg spacing (42 mm pitch): raise it for longer fobs, lower it to fit more pegs on a shorter plate. Bend angle (75°) and straight run (12 mm): lengthen the run for larger rings, ease the angle for a flatter peg. Hang hole (12 mm): resize to match your rack hook. Pairs with: any horizontal key rack with a post or screw head that fits the hole.
TANKER 3 Water
A matched set of eight small label plates with bold raised white lettering, styled like the enamel signage screwed to a garage wall, a shelf edge or the front of a storage bin. Each plate carries a single word — the four blue plates read ROAD, CURB, REAR and REAR, and the four red plates read SCENE, DECK, TANK and TANK — so a wall of bins, hooks, shelves or parking spots can be told apart at a glance. Colour does the sorting: blue for one group, red for the other, both with the same white lettering, so the two families stay distinguishable from across the room while reading as one set. The letters are thickened rather than enlarged, so the strokes carry weight without changing the plate size. The plates are plain rectangles with rounded corners and no fixing hole, leaving the full face free for the text — stick them on with double-sided tape or adhesive, or drill and screw them wherever they are needed. Dimensions Each plate: 1.5 in wide × 1 in tall (38.1 × 25.4 mm), 2 mm thick Rounded corners, no hanging hole Raised lettering: 0.8 mm proud of the face, strokes thickened for a heavier face Lettering centred horizontally and vertically on every plate Plates laid out 32 mm apart in two columns, blue set on the left, red set on the right Set contents Blue: ROAD, CURB, REAR, REAR Red: SCENE, DECK, TANK, TANK Print notes All eight plates sit flat on the bed and print without supports A single filament swap at letter height produces the two-tone face; painting the raised text works just as well The whole set prints in one go and comes off as eight separate tags The same layout takes any short word you want to swap in, as long as the plate size and the two-tone face stay the same.