Created 3 months ago
Description
A full-scale dimensional model of a standard closet shelf and rod assembly. The shelf sits above with integrated support brackets dropping down to hold the hanging rod securely.
Designed at a 1:1 scale to the requested dimensions, it includes:
Images

A storage case for two 31 mm round, 71 mm tall vials, with a separate snap-on lid. Body and lid are two separate pieces, laid out side by side so each can be exported as its own STL. Each vial sits in its own round pocket, with a 4 mm solid wall between the pockets so the vials never touch at the base. The pockets have 0.6 mm of clearance and a 3 mm floor. A finger slot on the front of each pocket makes lifting a vial out easier. The lid fits over the top of the body and clicks onto a shallow groove around the rim. It leaves room for the vial tops that stick out above the body. Vial size: 31 mm diameter, 71 mm tall Body height: 60 mm, 2.5 mm walls Lid: 5 mm overlap onto the body, with an inward snap bead Made with resin printers such as the Elegoo Mars in mind
A hexagonal box with a matching lid, printed as two separate pieces. The box is 50 mm tall and 80 mm across the corners, with 2.4 mm walls and a 3 mm floor. The lid is a 3 mm hexagonal plate with a 6 mm hollow lip underneath. The lip sits inside the box opening with about 0.4 mm of clearance per side, so the lid stays put without a tight press fit. Box: 80 mm across corners, 50 mm tall, chamfered base edge Lid: 80 mm across corners, 3 mm plate, 6 mm inner lip Print the lid flat with the lip facing up No supports needed for either piece
Caja con tapa y orejetas de cierre, ajustada para imprimirse en una cama de 220 × 220 mm como la de la Ender 3 Pro. El cuerpo mide 203 mm de largo y las orejetas ya no sobresalen tanto, así que cada pieza queda en 217 mm de ancho. Detalles Interior de 193 × 95 mm. 4 orejetas con agujero para insertos roscados M6. Tapa con solapa y ranura para junta de goma. Placa vertical con refuerzos. A tener en cuenta Cada pieza se imprime por separado; en el modelo aparecen una al lado de la otra solo para la vista.
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
Caja con tapa para insertos roscados M6 en cuatro orejetas de cierre, con medidas interiores de 200 × 95 × 40 mm y paredes de 5 mm. Qué lleva 4 orejetas exteriores con agujero de 8,4 mm y 8 mm de profundidad para insertos roscados M6 de 9 mm de diámetro exterior. Tapa de 10 mm de grosor con 4 agujeros avellanados de 6,4 mm. Solapa de tapa de 70 × 40 mm, con 10 mm de grosor y esquinas superiores con radio de 15 mm. Lleva un agujero central de 8 mm y otro de 6 mm a 25 mm del centro. Ranura de 1,5 mm en caja y tapa para un cordón de goma de unos 2 mm. Placa vertical de 60 mm con triángulos de refuerzo de 3 mm de grosor. Medida a comprobar El diámetro exterior real de los insertos. El agujero está pensado para 9 mm. No encaja Tornillos distintos de M6 en las orejetas, ni cordones de goma de más de 3 mm.
这是一套需要组装的、可多层叠加的茶包抽屉,按 PLA 打印设计:底座框架内装两组定滑轨与动滑轨,抽屉盒体沿轨抽出,前端用两颗 D4×2 磁铁吸合,四角堆叠卡扣让相同单元上下定位。打印件包括底座、抽屉盒体、动/定滑轨各 2 件、4 个堆叠卡扣和抽屉端板;组装用 M3×8 平头螺栓。 可改的起始尺寸 底座框架:140×110×32 mm,后部开窗;侧壁 3 mm。 抽屉盒体:外尺寸 126×98×26 mm;前壁 2 个 Φ4 磁铁沉孔,设计深 2.2 mm。 滑轨:定/动滑轨各 2 件,长 110 mm;动定之间留 0.2 mm 滑动间隙。滑轨为 2 mm 薄片,受底座侧壁厚度限制。 堆叠卡扣:42×18×14 mm,四角各一件;抽屉端板:106×28×6 mm。 紧固孔:M3 沉头过孔 Φ3.4 mm;磁铁:D4×2 mm。 换版时先动这几处 先改抽屉盒体的长宽高,底座和端板跟着放量,滑轨长度保持 110 mm 或按新行程加长。 0.2 mm 滑动间隙是抽拉手感的关键,材料收缩大时先调这里,不要先改轨形。 堆叠卡扣的 42×18×14 mm 决定层间定位;要叠更高或换更厚板材,优先改卡扣高度与卡口深度。 磁铁沉孔按 Φ4×2.2 mm 设计;想换 D5 或 D6 磁铁,直接放大沉孔与对应磁铁位。 M3 沉头孔为 Φ3.4 mm 过孔,螺栓头不会完全埋平;需要齐平就加深或扩大沉孔。 如果要继续做系列,这套盒体适合与同尺寸底座、不同深度的抽屉盒,以及带标签孔的端板配对;保持四角卡扣和滑轨接口不变,就能混搭层数。