Tokens 3d print
Created 1 months ago
Description
A 3D-printable card dispenser built for standard playing cards. The stack sits vertically, and a narrow 0.8 mm slot at the bottom front lets exactly one card pass through at a time, stripping off any cards that try to follow it.
Features a sliding track cutout in the floor for your thumb, and rests on 25 mm legs so you can pull a card without lifting the box off the table. A friction-fit lid keeps the rest of the deck secure.
- Holds one standard 40 mm stack of cards
- Bottom-dispensing slot (one card at a time)
- 25 mm elevated base for table-top access
- No supports required
Images
More like this
Explore more in Storage & Organization →
Mini 19-Cone Henna Carousel Stand
A compact two-tier henna cone stand: 110 mm trays, 60 mm apart, holding 19 cones tip-down, joined by a 25 mm central column and a screw cap. The top tray's 15 mm holes sit directly over 6 mm tip holes in the lower tray. A foot ring under the lower tray keeps cone tips off the table. Remix hooks Tray spacing: 60 mm now. Raise it for longer cones. Ring layout: 12 holes at 43 mm radius plus 7 at 25 mm radius. Wall between rings is about 3 mm, so adding holes means growing the tray. Tray diameter: 110 mm. Scale it up and add a third ring for more capacity. Hole size: 15 mm top, 6 mm bottom. Adjust to your cone brand. Pairs with: a turntable disc or non-slip mat under the foot ring.
Two-Piece Pro Controller Wall Holder
A 380 mm wall holder for a PS5 and a Switch Pro controller is too wide for most print beds, and a single plate can crack along its length. This version prints as two 190 mm halves that lock together with two butterfly keys. Fit and print Split line: centre of the plate, through the Yu-Gi-Oh! ring emblem Keys: two butterfly-shaped keys, 24 mm wide and 20 mm tall, 2.9 mm thick, printed flat Key pockets: cut 3.3 mm deep into the back face, 0.3 mm clearance all round Assembly: press the keys into the back pockets across the seam, then screw the halves to the wall. The wall holds the keys in Mounting: eight countersunk screw holes in total, four per half Printing: halves lie on their backs or stand on the shelf base. No supports are needed for the hollow blocks Pocket sizes are 166 mm wide and 70 mm deep, from typical controller sizes and not from measurements of a specific controller.
Staggered 5-Key Hook Extender
A tall back plate that hangs from a key rack and holds five keys on alternating left and right pegs, so fobs dangle without touching each other. The plate is 46.2 mm wide, 240 mm tall and 12 mm thick, with a 12 mm hang hole at the top right. Each peg is 8 mm in diameter, runs straight for 12 mm, then curves upward through 75° to keep rings seated. Remix hooks Plate thickness (12 mm): the easiest stiffness lever. Pegs are set into the plate face, so going thicker needs no other changes. Peg spacing (42 mm pitch): raise it for longer fobs, lower it to fit more pegs on a shorter plate. Bend angle (75°) and straight run (12 mm): lengthen the run for larger rings, ease the angle for a flatter peg. Hang hole (12 mm): resize to match your rack hook. Pairs with: any horizontal key rack with a post or screw head that fits the hole.
TANKER 3 Water
A matched set of eight small label plates with bold raised white lettering, styled like the enamel signage screwed to a garage wall, a shelf edge or the front of a storage bin. Each plate carries a single word — the four blue plates read ROAD, CURB, REAR and REAR, and the four red plates read SCENE, DECK, TANK and TANK — so a wall of bins, hooks, shelves or parking spots can be told apart at a glance. Colour does the sorting: blue for one group, red for the other, both with the same white lettering, so the two families stay distinguishable from across the room while reading as one set. The letters are thickened rather than enlarged, so the strokes carry weight without changing the plate size. The plates are plain rectangles with rounded corners and no fixing hole, leaving the full face free for the text — stick them on with double-sided tape or adhesive, or drill and screw them wherever they are needed. Dimensions Each plate: 1.5 in wide × 1 in tall (38.1 × 25.4 mm), 2 mm thick Rounded corners, no hanging hole Raised lettering: 0.8 mm proud of the face, strokes thickened for a heavier face Lettering centred horizontally and vertically on every plate Plates laid out 32 mm apart in two columns, blue set on the left, red set on the right Set contents Blue: ROAD, CURB, REAR, REAR Red: SCENE, DECK, TANK, TANK Print notes All eight plates sit flat on the bed and print without supports A single filament swap at letter height produces the two-tone face; painting the raised text works just as well The whole set prints in one go and comes off as eight separate tags The same layout takes any short word you want to swap in, as long as the plate size and the two-tone face stay the same.
Apothecary Grid Hinged Pill Box
A pharmacy-drawer grid in miniature: thirty round wells in a 6×5 layout, topped by a lid that swings open on a real pin hinge at the back edge. The lid prints flat beside the tray and clicks into the hinge ears once a short pin is slid through. 30 slots, 16 mm wide and 14 mm deep Hinge pin hole sized for a 1.75 mm filament offcut, about 56 mm long Front finger tab on the lid for easy opening Lid and tray print without supports in separate pieces
4 Bölmeli Vidalı Kapaklı Saklama Kabı
210 mm çapında ve 60 mm yüksekliğinde yuvarlak bir saklama kabı. İçi çapraz iki bölmeyle dört eşit gözeye ayrılmış; kapak kapalıyken gözeler birbirine karışmaz. Kapak, gövdenin üstündeki dış dişe vidalanarak kapanır, böylece taşırken kendiliğinden açılmaz. Gövde duvarları, taban, bölmeler ve kapak üstü ince tutulmuş, böylece baskı kısa sürer ve malzeme az gider. Gövde: 210 mm çap, 60 mm yükseklik, dört eşit bölme Kapak: 210 mm çap, 14,3 mm yükseklik, gövdeye vidalanır Diş: 12 mm boy, 5 mm adım, 3 ağızlı (hatve 15 mm), 0,5 mm boşluk; kapatmak için yaklaşık 0,8 tur (yaklaşık 290°) çevirmek yeterlidir Et kalınlıkları: yan duvar ve taban 1,6 mm, iç bölmeler 1,2 mm, kapak üstü 2,4 mm Baskı: gövde ve kapak ayrı ayrı basılır; kapak ters çevrilmeden, düz yüzü tablaya gelecek şekilde basılır Diş çapı 204 mm'ye çıkarıldığı için gövdenin üst kısmındaki basamak her yanda yaklaşık 3 mm'ye iner; boyun iç çapı 197 mm'dir. Dişin dibindeki duvar ince kaldığından o bölgeyi basarken katman ayarlarına dikkat etmek gerekir. Bölmeler dişli boyun bölgesinde de gövdenin içinde kaldığı için kapak takılıyken de ayrım korunur. Geniş çapı sayesinde dökme parçaları, vida ve küçük donanımı ya da atölye malzemesini tek kapta ayrı gözelerde tutmak için uygundur.