Four-Deck UNO Vault With Cap
Created today
Description
A card-table caddy for four UNO variants: Classic, No Mercy, All Wild and Flip. Each deck lies flat in its own slot, split by 2 mm dividers, and a slip-over cap closes the box so nothing shuffles between slots.
- Slots sized from the supplied card dimensions plus clearance
- Walls 54 mm tall, so the tallest deck stays below the rim
- Finger hole through the floor of each slot to push decks up
- Front scoops for gripping
- Cap prints upside down and fits snugly over the outside of the rim
Photos
Technical views
More like this
Explore more in Storage & Organization →
Open-Frame Armored Commander Deck Box
A Commander deck box wearing skeletal corner armor: each of the eight TPU bumpers is cut into an open frame, so only a rim hugging the box's edges remains, like the corner guards on a vintage steamer trunk. The box holds around 100 sleeved cards, with a lift-off lid and a magnetic swap-in emblem on the front. Window cuts: a rounded rectangle at 80% of each face (top, front, side) is cut through the bumpers. Bumpers: all eight corners are guarded from three directions, with scooped corners. Emblem: a 32 mm tile held by two 6 x 2 mm magnets. Lid: deep cap with a chamfered top edge and an inner lip.
Cat Head Box
Une boîte de rangement simple reprenant la silhouette d'une tête de chat, conçue pour s'imprimer sans supports. Structure : Base creuse de 40 mm de haut avec des parois de 2 mm. Couvercle : S'emboîte via une lèvre interne, avec un jeu de 0.4 mm pour un ajustement facile. Impression : Le couvercle est déjà orienté face plate vers le plateau d'impression.
Support 25 Clés USB
Un support de bureau lourd et stable conçu pour ranger et organiser 25 clés USB en un seul endroit. Variables à ajuster Espacement (28 mm x 23 mm) : Pensé pour accepter la plupart des corps de clés USB sans qu'elles se chevauchent. Peut être resserré si vous n'avez que des clés très fines. Taille des encoches (14 mm x 7,5 mm) : Les fentes offrent un jeu confortable autour d'un connecteur USB-A standard. Profondeur (12 mm) : Laisse les clés bien droites tout en conservant 3 mm de matière pleine au fond du bloc (hauteur totale de 15 mm).
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.
Slim Tiered Playing Card Rack
What it's for A sleek, tiered playing card holder designed to display up to five rows of cards. It features 15-degree angled blind grooves to securely pitch cards back at a comfortable viewing angle, with progressively taller tiers ensuring full visibility for the rear rows. Dimensions Overall footprint: 220 mm wide × 85 mm deep Height: 75 mm (at the rear tier) Tiers: 5 rows, each stepping up by 15 mm Internal: Fully hollowed with an enclosed internal void, featuring 4 mm robust walls, a continuous solid base, and internal bridging ribs to print cleanly while conserving filament. Print notes Designed to be printed flat on its base without external supports. The internal structure consists of safely bridged spans (~39 mm each) supported by internal ribs, meaning you shouldn't need infill to support the roof layers.
Standard Card Interlocking Holder
A five-row holder for standard 63.5 × 88.9 mm playing cards. The deck tilts cards back at a 15-degree angle for easy reading without letting them spill. The holder breaks down into two halves using a 3-tab interlocking jigsaw joint laid flat into the base. The base stays completely solid underneath to protect the cards, and the joint pulls straight apart vertically when you need to pack it away. Specs Total Assembled Length: 330.2 mm (13 inches) Clearance: 0.25 mm per side on the interlocking puzzle tabs Groove Floors: Solid, minimum 3 mm thick beneath the slots