Created 28 days ago
Remixed 2 times
Description
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens.
Images
A compact two-tier henna cone stand: 110 mm trays, 60 mm apart, holding 19 cones tip-down, joined by a 25 mm central column and a screw cap. The top tray's 15 mm holes sit directly over 6 mm tip holes in the lower tray. A foot ring under the lower tray keeps cone tips off the table. Remix hooks Tray spacing: 60 mm now. Raise it for longer cones. Ring layout: 12 holes at 43 mm radius plus 7 at 25 mm radius. Wall between rings is about 3 mm, so adding holes means growing the tray. Tray diameter: 110 mm. Scale it up and add a third ring for more capacity. Hole size: 15 mm top, 6 mm bottom. Adjust to your cone brand. Pairs with: a turntable disc or non-slip mat under the foot ring.

Gavetas e bancadas viram bagunça quando parafusos, cabos e peças pequenas se misturam. Esta caixa organizadora separa tudo em 6 compartimentos fixos, em grade de 3 x 2. Medidas e impressão Tamanho externo: 180 x 120 x 50 mm Paredes e fundo: 2 mm Divisórias: 2 mm, 5 mm mais baixas que a borda Cada compartimento mede cerca de 56 x 57 mm por dentro Imprime sem suportes, com o fundo apoiado na mesa PLA ou PETG, com 0,2 mm de altura de camada
A tall back plate that hangs from a key rack and holds five keys on alternating left and right pegs, so fobs dangle without touching each other. The plate is 46.2 mm wide, 240 mm tall and 12 mm thick, with a 12 mm hang hole at the top right. Each peg is 8 mm in diameter, runs straight for 12 mm, then curves upward through 75° to keep rings seated. Remix hooks Plate thickness (12 mm): the easiest stiffness lever. Pegs are set into the plate face, so going thicker needs no other changes. Peg spacing (42 mm pitch): raise it for longer fobs, lower it to fit more pegs on a shorter plate. Bend angle (75°) and straight run (12 mm): lengthen the run for larger rings, ease the angle for a flatter peg. Hang hole (12 mm): resize to match your rack hook. Pairs with: any horizontal key rack with a post or screw head that fits the hole.
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
Nook is a round pencil cup sized to hold pens, pencils, markers and short rulers upright on a desk. The design keeps a clean, fully circular profile — no flat back, no corners — so it reads as a plain cylinder from every side. What sets this version apart is a wall of openings cut all the way around and up the side: three staggered rows of small round holes that let you see at a glance what's inside, let the cup breathe, and keep the barrel light. At 80 mm across and 70 mm tall it takes a full handful of writing tools while staying low enough to reach into from a seated position. Dimensions Diameter: 80 mm, fully round Height: 70 mm Walls: 4 mm Footprint: 80 × 80 mm Side openings: 36 round holes, 10 mm across, in three staggered rows of 12, spread around and up the cup wall Features Full circle profile with no flat back — the same silhouette from any angle A staggered grid of 10 mm holes around the side wall, small enough to leave solid wall between them Base and top rim stay solid, so the cup holds its shape and stands straight Wide 80 mm mouth for pencils, pens, markers and short rulers 4 mm walls give it enough weight at the base to stay put while you pull a pen out Freestanding: it sits directly on a desk, shelf or tray with nothing to fix or hang Print notes Prints as a single piece with no supports. Print it upright as it sits on the plate so the walls and the round holes stay clean, or lay it on its side if you prefer a smoother inner surface and can accept a light support under the outer curve. A slightly wider brim helps on taller, narrow prints.
A round 88 mm ornament disc, 4.8 mm thick, with a grid of LEGO-compatible studs on the face and a hanging loop at the top. Printed in red, flat, with no supports. Remix hooks Stud diameter: 5.0 mm now (standard is 4.8 mm). Raise it to 5.05 for a firmer grip, or drop it to 4.9 if bricks sit too tight on your printer. Stud height: 1.8 mm. Taller studs give a deeper grip but need more bridging care. Disc thickness: 4.8 mm, or 1.5 LEGO plates. Use 3.2 mm for one plate or 9.6 mm for a full brick height. Disc diameter: 88 mm on an 8 mm stud pitch. The stud grid is cut to a 37 mm radius, which leaves a plain rim. Loop: 13 mm outer, 5.5 mm hole. Widen it for ribbon. Pairs with: 1x1 and 2x2 bricks, tiles, and small minifigure scenes.