o-ring-sealed-box-20260525
Created 5 months ago
Description
An airtight utility and hardware storage container designed around a standard continuous 1/8" O-ring seal. Perfect for protecting sensitive components, shielding camping gear from moisture, or securing hardware outdoors.
- Internal capacity: 1" × 8" × 4"
- Seal format: Integrated continuous compression channel for standard 3mm (~1/8") O-rings
- Fastening: 6 standard #8 machine screw clearance holes (corner and midpoint reinforcement)
- Underbelly: Hex-nut traps sized for drop-in assembly
- Profile: Rounded routing edges for unkinked continuous seal placement
Images
More like this
Explore more in Storage & Organization →
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
Mister Box Holder with Open Front
A wall-mounted cradle for a 2.25" x 4.75" x 2" mister box, sized with extra width clearance and a little extra depth so the box slots in easily but can't tip forward out of it. The front is open below a solid top rim so the buttons stay reachable, and a low lip along the bottom front edge holds the box in. Two identical ears on the back face carry countersunk screw holes for mounting to the side of furniture. Full 4.75" (120.65 mm) wall height 10 mm width gap, 3 mm depth gap Cord notch in the left rim only, 15 mm wide, centered 1.5" from the inside back wall, open at the top Window cutouts on the sides to save filament Two back ears with countersunk screw holes
Two-Piece Gridfinity Caliper Box
A 6 x 3 unit Gridfinity caliper box split at the middle into two halves, each about 126 x 126 x 25.4 mm, so each fits a 150 mm print bed. Two dovetail keys join the halves. The stepped pocket holds a 9.25 in caliper: a 15.9 mm body slot and a 78 x 97.5 mm head recess, both 12.7 mm deep. The stacking lip and finger scoops are kept. Remix hooks Split position: the cut is at X = 0, on a Gridfinity cell boundary. Moving it in whole 42 mm steps keeps the cells intact. Dovetail size: 8 mm at the root, 13 mm at the tip, 16 mm tall, at Y = ±35. The socket has 0.25 mm clearance. Loosen or tighten it to suit your printer. Joint type: swap the dovetails for round pins or add glue grooves. Pairs with: other Gridfinity bins on a 42 mm baseplate.
Drawer Sleeve Box With Mounting Pad
Open-top rectangular sleeve, 86 x 52 x 127 mm, for a sliding drawer. Smooth interior, 1.6 mm floor, sides and front, 2.4 mm back wall. A raised 40 x 40 x 3 mm pad on the back carries two M3 nut traps. Remix hooks Pad position: top edge sits 10 mm below the rim; pad is centered in X. Move or resize freely. Nut traps: 5.7 mm hex, 2.5 mm deep, 25 mm apart, with 3.4 mm blind holes behind them. Blind holes stop 0.8 mm short of the inside; thicken the back wall to go deeper. Edges: 3 mm vertical rounding, 6 mm 45° bottom chamfer (prints without supports). Drains: two 3 mm holes at X = ±20 mm. Pairs with a matching drawer 3 to 4 mm smaller in each direction.
Swivel Tooth Stash Box
A fluted cylinder stash box featuring a swing-open lid and a custom dental logo on top. The lid snaps securely into place with a concealed locking pin, making it perfect for holding small desktop items. Swivel Action: Swings smoothly and clicks closed via a small detent on the rim. Fluted Base: Deep vertical cuts around the cylinder provide plenty of grip. Raised Engraving: A custom tooth outline frames "United Smiles Dentistry" cleanly on the lid.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.