Print-In-Place Advent Drawers
Created today
Description
What it's for
This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way.
The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues.
Dimensions
- Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep.
- Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep.
- Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats).
- Clearances: 0.5 mm on all sides for smooth, bind-free sliding.
Print notes
- Supports: None. The entire unit bridges perfectly on its own.
- Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini).
- Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Images
More like this
Explore more in Storage & Organization →
4-Compartment Kitchen Organizer
A small, straightforward drawer organizer divided into four compartments. One wide compartment runs the length of the tray for standard utensils, while the back half is split into three smaller bays for loose items. Dimensions Overall size: 150 mm long × 100 mm wide × 35 mm tall Wall thickness: 2 mm solid walls and dividers Long bay: ~146 mm × 47 mm (ideal for small spoons or forks) Small bays: ~47 mm × 47 mm each Print notes Designed to print flat on its base without supports. Generous corner radii keep things from getting stuck in the corners. PLA or PETG both work fine for drawer use.
Cascading Hex Organizer
A minimalist, honeycomb-inspired desk organizer that steps up in height to hold everything from SD cards to tall pens. Its stepped layout is optimized for rapid support-free 3D printing. Zero Supports Required: Designed to print flat on the bed with no overhangs. V-Groove Details: Chamfered edges create a premium architectural look where the cells meet. Stepped Heights: Makes smaller items just as easy to grab as tall ones.
Offenes Schreibtischregal mit Rampe
Schreibtische müllen immer von der Mitte her zu. Dieses Regal hebt den Kleinkram aus dem Weg und teilt die Fläche in der Mitte mit einer harten Rampe – links liegt das Fach tief für flaches Zeug, rechts hoch, damit darunter noch Platz für größeres Zubehör bleibt. Alles bleibt zugänglich und nichts verhakt sich. Eckdaten Spannweite: 450 mm Standfläche (Tiefe): 180 mm Höhe: 250 mm Druck: Wird flach auf der Rückseite liegend gedruckt und kommt komplett ohne Stützstrukturen aus.
Standard Card Interlocking Holder
A five-row holder for standard 63.5 × 88.9 mm playing cards. The deck tilts cards back at a 15-degree angle for easy reading without letting them spill. The holder breaks down into two halves using a 3-tab interlocking jigsaw joint laid flat into the base. The base stays completely solid underneath to protect the cards, and the joint pulls straight apart vertically when you need to pack it away. Specs Total Assembled Length: 330.2 mm (13 inches) Clearance: 0.25 mm per side on the interlocking puzzle tabs Groove Floors: Solid, minimum 3 mm thick beneath the slots
130mm Tubeless Repair Kit Case
A rigid three-piece storage case designed for tubeless tyre repair kits. The base features an inset lip that locks the lid in place, secured by a snap-fit C-clamp latch that mounts to an integrated front axle. Dimensions: 130 mm x 85 mm x 35 mm combined. Wall Thickness: 2.5 mm throughout. Clearances: 0.3 mm on the lid slip-fit, 0.5 mm width clearance for the latch. Print Orientation: All three pieces are laid flat on the bed. No supports required.
65mm Wood Hook Phone Bracket
A heavy-duty hook bracket to suspend a phone over a 60mm wooden beam or headboard. The main channel is sized at 65mm for clearance, dropping a device tray down 65mm from the top edge. Fitment: 65mm interior gap clears standard 60mm stock. Tray Specs: 16mm deep with a 3mm inward tilt to keep the device seated against the backrest. Width: 50mm overall extrusion. Printability: Designed to be printed flat on its side. Requires no supports.