Sliding Lid iPhone 11 Box
Created today
Description
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open.
Remix hooks
- Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones.
- Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer.
- Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot.
- Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open.
Print both pieces flat, no supports needed.
Images
More like this
Explore more in Storage & Organization →
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.
Drawer Sleeve Box With Mounting Pad
Open-top rectangular sleeve, 86 x 52 x 127 mm, for a sliding drawer. Smooth interior, 1.6 mm floor, sides and front, 2.4 mm back wall. A raised 40 x 40 x 3 mm pad on the back carries two M3 nut traps. Remix hooks Pad position: top edge sits 10 mm below the rim; pad is centered in X. Move or resize freely. Nut traps: 5.7 mm hex, 2.5 mm deep, 25 mm apart, with 3.4 mm blind holes behind them. Blind holes stop 0.8 mm short of the inside; thicken the back wall to go deeper. Edges: 3 mm vertical rounding, 6 mm 45° bottom chamfer (prints without supports). Drains: two 3 mm holes at X = ±20 mm. Pairs with a matching drawer 3 to 4 mm smaller in each direction.
Standard Card Interlocking Holder
A five-row holder for standard 63.5 × 88.9 mm playing cards. The deck tilts cards back at a 15-degree angle for easy reading without letting them spill. The holder breaks down into two halves using a 3-tab interlocking jigsaw joint laid flat into the base. The base stays completely solid underneath to protect the cards, and the joint pulls straight apart vertically when you need to pack it away. Specs Total Assembled Length: 330.2 mm (13 inches) Clearance: 0.25 mm per side on the interlocking puzzle tabs Groove Floors: Solid, minimum 3 mm thick beneath the slots
Stash Box With Rolling Groove2
A stash box dimensioned precisely to 6" x 4" x 2". The lid features an inner alignment flange for a secure slip-fit when closed. When removed and inverted, the lid acts as a functional tray, featuring a solid raised block with a 130mm long V-notch engineered into the center to cradle rolling papers. Dimensions Overall Box Size: 152.4mm x 101.6mm x 50.8mm (6" x 4" x 2") V-Notch Length: 130mm (accommodates standard and king-size papers) Wall Thickness: 2mm throughout the base Print Notes Both parts are oriented flat on the build plate in their optimal printing positions. The V-notch prints perfectly without supports due to its self-supporting 45-degree overhang geometry. A 0.6mm clearance tolerance is built into the lid lip to allow smooth opening and closing right off the printer.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.