Snap-On Double Bar Shelf
Created 1 months ago
Description
What it's for
A wide, flat shelf designed to snap perfectly over a pair of parallel 15mm bars. Instead of resting loosely, the underside features six discrete snap-clips (three per bar) with a slightly pinched opening, allowing it to firmly grip the rails and resist sliding or tipping.
Dimensions
- Overall Size: 220 mm wide × 280 mm deep.
- Bar Spacing: Fits bars spaced 210 mm apart from the very front edge of the front bar to the very back edge of the back bar.
- Bar Fit: 15.5 mm cavity with a 14.2 mm snap opening, tuned for standard 15 mm rods.
Print notes
The shelf is modeled "upside down." Print it flat on its top surface; the snap clips will point upwards and print cleanly without supports. PETG is highly recommended to give the clips the necessary flex to snap onto the bars without shattering.
Images
More like this
Explore more in Storage & Organization →
Screw-Through Dowel Shelf Bracket
A two-part wall bracket for holding a 13 mm wooden dowel, intended as a filament spool shelf. A narrow wall plate carries a ledge that takes the vertical load, and a separate flat-printed arm rests on that ledge. One screw passes through the arm's back flange and the wall plate into the wall, locking the two parts together. The screw head sits in a recess in the arm. Wall plate: 24 mm wide, 84 mm tall, with a ribbed ledge under the arm Arm: 12 mm thick, printed on its side with no supports Dowel hole: 13.6 mm, 150 mm out from the wall plate Fixing: one screw near the top, shared by both parts Print two sets for a pair of brackets
130mm Tubeless Repair Kit Case
A rigid three-piece storage case designed for tubeless tyre repair kits. The base features an inset lip that locks the lid in place, secured by a snap-fit C-clamp latch that mounts to an integrated front axle. Dimensions: 130 mm x 85 mm x 35 mm combined. Wall Thickness: 2.5 mm throughout. Clearances: 0.3 mm on the lid slip-fit, 0.5 mm width clearance for the latch. Print Orientation: All three pieces are laid flat on the bed. No supports required.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
C Clip for 9V Battery Container
What it's for A snap-in C clip that holds a 22 x 33 mm 9 V battery container. The opening sits in the front long wall, so the container presses in and pulls out when the battery needs changing. Dimensions Inside pocket: 22 x 33 mm Height: 20 mm Wall thickness: 2.5 mm Opening: 27 mm wide, leaving 3 mm of retaining wall on each side Outside: 38 x 27 mm Remix ideas Widen the opening to 28 or 29 mm for an easier release. Add a mounting tab or screw holes on the back wall. Print in PETG or nylon for better flex at the snap.