Soporte Behringer JT-4000 Micro

Sentinel Deck Vault

A robust, two-piece deck box built for transport and easy access. Designed to hold 100 double-sleeved 63x88mm trading cards, it features a snug snap-fit lid to prevent spills in your bag. Secure Closure: Friction-fit lip with spherical snap detents. Easy Access: Deep thumb cutouts on the front and back let you grab the whole deck at once. Sturdy Build: Thick 2.4mm outer walls for solid protection.

7 days agoRemix →

Large Cable Organizer Box

A high-capacity cable management box with a fitted drop-in lid, sized to house bulky power strips, large transformers, and excess cable coils. The rear panel features two mouse-hole style arch cutouts seated flush with the interior floor for easy drop-in cable routing without requiring cables to be threaded through tight slots. What it's for Concealing power strips, power bricks, and cable runs on desktops or floors Floor-level cable pass-through that keeps cords flat against the surface Dust protection with an easy-access lift-off lid Dimensions Internal Clearance: 215.9 mm (8.5") W × 292.1 mm (11.5") D × 127.0 mm (5.0") H Wall Thickness: 3.0 mm Port Size: 40 mm wide × 64 mm high arched openings flush to the floor plate Outer Footprint: 221.9 mm × 298.1 mm × 133.0 mm (excluding lid hover offset) Print notes Print the box base-down with no supports needed for the arched ports. The lid prints flat on its top face for maximum surface quality and bed adhesion. Requires a build volume of at least 300 mm × 225 mm.

2 hours agoRemix →

Trinket Box With Captive Hinge

Most 3D-printed boxes rely on thin plastic living hinges that fatigue and snap off after a week of use, or require separate filament fragments as pins that eventually back out. This print-in-place trinket box uses a five-knuckle mechanical barrel hinge with integrated teardrop pins to prevent bridging collapse. A front thumb-tab with an offset detent provides a positive snap closure so the lid doesn't flap open when jostled in a drawer. Dimensions: 70 mm x 50 mm x 30 mm overall footprint. Walls: 2 mm solid perimeters for rigidity. Tolerances: 0.4 mm clearance inside the hinge barrel to prevent the knuckles from fusing during extrusion. Printing: Print fully closed, flat on the base. Requires no supports.

3 hours agoRemix →

Litteä lääkekotelo

Tämä ohut suojakotelo on suunniteltu pelkkien läpipainolevyjen kuljettamiseen. Se pitää lääkkeet ehjinä taskussa tai laukussa ilman alkuperäisen pahvipakkauksen viemää tilaa. Ominaisuuksia: Matalampi profiili, joka säästää tilaa Kitkasovitteinen kansi pitää kotelon kiinni Pyöristetyt kulmat tekevät siitä taskuystävällisen

4 hours agoRemix →

Finn's Stash Chest

A small, sturdy stash box modeled after a classic domed chest, personalized with "Finn" on the front. Features: Dimensions: 80mm wide by 50mm deep; stands 51mm tall when closed. Fit: Designed as two separate pieces. The base features a 4mm registration lip with 0.4mm clearance to keep the lid securely in place without hinges. Printability: Both parts print flat on the bed with no supports required. Thick walls give the base a satisfying, substantial feel.

12 hours agoRemix →

Mechanical 40-Quarter Dispenser

A fully mechanical, gravity-fed coin magazine tailored for standard U.S. quarters. Designed to slip into a pool cue bag, it stores a full $10 roll vertically and cleanly dispenses exactly $1 (four quarters) per cycle into the palm of the hand. The mechanism relies on a two-stage sliding escapement. In the resting position, the bottom four coins sit perfectly flush inside the 7.2mm-thick slider pocket. When the thumb tab is pulled outward, a chamfered ramp on the top trailing edge of the pocket catches the fifth quarter and guides it smoothly onto the solid tail of the slider, suspending the rest of the stack. Once the pocket aligns with the drop chute at full extension, the isolated four quarters fall through. A captive printed pin mounted from the base runs in an internal track on the slider, acting as a hard travel limit for both the pull and return strokes. Remix & Tuning Hooks Threaded Cap: The top of the magazine tube now features a coarse 4mm-pitch thread, securing the cap firmly for travel. Magazine Height: The tube is dimensioned at 75mm to easily clear forty 1.75mm-thick quarters. Snip the cylinder height in the code to make a shorter 20-coin version. Coin Bore: Currently 25.2mm to allow 0.47mm radial clearance for a 24.26mm quarter. Tweak this offset for other currencies or tokens. Slider Thickness: The exact 7.2mm thickness dictates the dispense count (four coins). Scaling this Z-dimension alters how many coins drop per pull. Tolerances: The slider track relies on a 28.5mm bridge in the main body. If your printer sags on bridges, the slider can be sanded lightly, or the track height (7.6mm) can be nudged up.