Triglide Buckle With Paracord Tab
Created 1 months ago
Description
Straps always leave a dangling tail, and standard buckles give you nowhere to tie a pull-loop or secure the end. This adds a solid extension to a standard 1-inch tri-glide, featuring a dedicated hole to anchor a paracord knot.
Specs
- Webbing: Fits standard 1-inch (25.4mm) straps.
- Hole: 5.5mm diameter (clears standard 550 paracord, catches a stopper knot).
- Printing: Prints flat, no supports needed.
Photos
Technical views
More like this
Explore more in Storage & Organization →
Hollow Vibration Casing
A sturdy 86x21mm hollow enclosure with a rounded tip and an open base. The internal cavity strictly follows the outer profile, ensuring a uniform wall structure throughout. Dimensions: 21mm outer diameter, 86mm overall height Wall thickness: 2mm Base: Flat, open end with a 1mm exterior chamfer for printability and comfortable handling
Asymmetric 16-Slot Makeup Organizer
A single-piece makeup and vanity organizer built to the specified 200x140x90mm volume. The layout uses an asymmetric stepped profile to match compartment depths to their contents while maintaining a clean, minimalist silhouette. All interior vertical edges feature a 3mm radius to prevent powder buildup, and the outer shell carries an 8mm continuous radius. Specifications Dimensions: 200mm (W) × 140mm (D) × 90mm (H) overall. Brush Storage: Two rear compartments (90mm deep) sized for long-handled tools. Creams & Perfume: Twin mid-tier compartments (60mm deep) accommodating standard jars and bottles. Lipstick Grid: 16 independent 21.5mm square slots arranged in a 4×4 matrix (45mm deep). Jewelry Tray: Shallow front-left basin (30mm deep) for rings and small items. Printability: 2.4mm uniform wall and floor thickness. Prints flat without supports.
150mm Tapered Hair Tie Stand
A vertical storage stand designed to hold hair ties. The central post tapers continuously from base to tip, allowing elastic bands of varying diameters to settle at their natural resting heights. A wide, thick base prevents the assembly from tipping under off-center loads or when bands are removed. Specifications Post Dimensions: 150mm height, tapering from a 50mm base diameter to a 25mm upper diameter. Base Dimensions: 120mm diameter and 25mm thickness for structural stability. Cap: 25mm spherical terminal to prevent snagging during removal. Print Recommendations: High-density infill in the base section is required to provide the intended counterweight.
Caja Secreta con Llave Clásica
Una caja fuerte impresa en 3D que esconde su apertura a plena vista. En lugar del típico tirador, la tapa se asienta completamente a ras y requiere una llave física estilo tradicional para desenroscarla. El interior está optimizado con un techo cónico, por lo que imprime limpio sin necesidad de soportes. Características del montaje Impresión sin soportes: La cámara y la rosca se imprimen directo en la base. Llave dentada: Perfil plano tipo casa con agujero para llevarla en el llavero. Seguridad visual: La tapa a ras evita poder girarla con los dedos.
Tokens 3d print
A 3D-printable card dispenser built for standard playing cards. The stack sits vertically, and a narrow 0.8 mm slot at the bottom front lets exactly one card pass through at a time, stripping off any cards that try to follow it. Features a sliding track cutout in the floor for your thumb, and rests on 25 mm legs so you can pull a card without lifting the box off the table. A friction-fit lid keeps the rest of the deck secure. Holds one standard 40 mm stack of cards Bottom-dispensing slot (one card at a time) 25 mm elevated base for table-top access No supports required
Teardrop Sticker Dispenser
A compact, teardrop-shaped dispenser designed specifically for sticker rolls. The two halves snap together smoothly to fully enclose the roll, protecting the stickers and keeping the tape aligned. Design Details Capacity: Fits rolls up to 95mm outer diameter and 16mm width. Interlock: 5mm deep stepped lip with a 0.3mm radial clearance for a secure, tool-free friction fit right off the bed. Walls: 4mm thick for rigidity, stepping down seamlessly into the inner cavity. Exit: A simple 18mm front slot lets the tape pull freely without snagging. Both halves print flat on their outer faces without supports. If you find the friction fit too tight or too loose on your printer, the clearance parameter is the first thing to adjust.