Made by a Guest
Created 3 months ago
Description
A sturdy wall-mounted shelf featuring a J-profile design with open sides. Built specifically to support moderate loads up to 2 kg, it includes a generous structural fillet at the rear corner and three countersunk mounting points to distribute weight evenly against the wall. A pronounced front lip keeps displayed items securely in place.
Mounts directly to a flat surface using three standard flathead or countersunk screws (up to 4.5 mm thread diameter, 9 mm head). Suitable wall anchors are recommended based on the mounting surface to achieve the full 2 kg load capacity.
Photos
Technical views
Spiral shoe rack with six 60° steps around a central column on a round base, one pair of shoes per step. Each step has a dovetail tongue that slides down into a matching slot in the column, so steps can be removed or attached individually. Steps: 18 mm flat plates, 4 mm outer lip, 90 mm rise per step Overall size: 600 mm diameter, 540 mm tall Base: 300 mm diameter, 12 mm thick, chamfered Clip: dovetail 15 mm deep, 0.3 mm slot clearance Removal: lift the step straight up Print steps flat; column upright; large size may need scaling or sectioning

What it's for A four-compartment cutlery separator tray for a drawer, with semi-round finger cutouts in each divider so utensils lift out easily. Dimensions Overall height: 30 mm, with a 3 mm base and 3 mm walls Three compartments 240 mm long: 50, 60 and 65 mm wide One 55 mm wide, 185 mm long compartment beside the 65 mm one Finger cutouts: 24 mm diameter semicircles centred on each divider Remix ideas Change the cutout radius for deeper or shallower scoops Split the tray into pieces for smaller print beds Add a lip or feet for drawer grip
A three-tier slatted shoe rack, 500 × 300 × 480 mm, holding six pairs (two per shelf), now with decorative trim. Remix hooks Side diamonds: 22 mm diamond cutouts on each side panel, two per tier. Change the size, count or shape (hexagon, circle) to taste. Scalloped crown: 30 mm half-round bumps along the top of the back panel, spaced 50 mm. Widen the spacing for a calmer look. Corner finials: 18 mm spheres on the four top corners. Swap for cones or pyramids. Pairs with: splitting into panels for printing; the 8 mm wall suits dowel or screw joints. Dimensions to keep: shelf spacing (40/190/340 mm) sets shoe clearance.
A minimalist two-piece sliding storage drawer: a ribbed outer housing with an open front and a separate inner drawer with a flush, handle-free face. The housing measures 100 × 150 × 60 mm with 10 mm rounded outer corners and 1.6 mm walls. Vertical ribbing stiffens the side walls, and thin 45° guide rails keep the drawer aligned. The guide rails and side stop tabs stay inside the outer walls, with only the ribs standing proud by design; the front ends of the rails stop inside the rounded front corners. The top is an open frame with a 12 mm solid rim, thickened to 3.4 mm so the stacking recess does not cut through. The drawer slides on the rails and locks closed with rounded snap bumps that seat into grooves in the housing. Push the drawer inward to release the bumps; the rear U-shaped leaf spring then pushes it forward. The spring is 0.95 mm thick and 40 mm wide, anchored to the inner back wall and touching the floor only where it meets that wall. A 45° chamfer under its bottom edge lifts the loop clear of the floor as it runs forward, so it flexes freely and still prints without supports — the trade-off is a shorter front loop, so the spring is on the soft side. A 45° finger bevel under the bottom front edge gives a hidden pull once the drawer has popped out. Flexible side stop tabs catch pockets near the back of the drawer, limiting travel to about 95 mm; press the tabs aside to remove the drawer fully. The stop pockets are 1.2 mm deep with 1.4 mm of solid wall behind them. The housing also stacks: a 1.5 mm bottom foot, inset 2.2 mm with a 45° chamfer, sits in a matching 1.8 mm recessed step on the top rim with 0.3 mm clearance. Housing: 100 × 150 × 60 mm, ribbed sides, open top with 12 mm rim, 10 mm rounded corners, 1.6 mm walls Drawer: 95.7 × 135 × 53.2 mm, flush front, no handle, side snap bumps Release: push-push detent with rear U-spring Pull: hidden 45° finger bevel under the front bottom edge Stop: flexible side tabs limit travel to about 95 mm; press aside for full removal Stacking: 1.5 mm bottom foot and matching 1.8 mm top recess Printing: two separate pieces, no supports, overhangs 45° or shallower Tuning: spring force and detent interference may need adjustment after a test print

A storage case for two 31 mm round, 71 mm tall vials, with a separate snap-on lid. Body and lid are two separate pieces, laid out side by side so each can be exported as its own STL. Each vial sits in its own round pocket, with a 4 mm solid wall between the pockets so the vials never touch at the base. The pockets have 0.6 mm of clearance and a 3 mm floor. A finger slot on the front of each pocket makes lifting a vial out easier. The lid fits over the top of the body and clicks onto a shallow groove around the rim. It leaves room for the vial tops that stick out above the body. Vial size: 31 mm diameter, 71 mm tall Body height: 60 mm, 2.5 mm walls Lid: 5 mm overlap onto the body, with an inward snap bead Made with resin printers such as the Elegoo Mars in mind
Cajetín de aire industrial, un canal rectangular hueco que deja una cara larga abierta para acceder al interior. Dos pestañas planas en los extremos permiten fijarlo con tornillos de 3 mm. Medidas: 170 × 33 × 30 mm Paredes de 2,5 mm Dos pestañas con agujero de 3,4 mm Se imprime apoyado sobre su base