10mm Speaker Wire Tie Saddle
Created 1 months ago
Description
A flat-mount zip tie saddle designed to route speaker wire along skirting boards. The base sits flush against the mounting surface, accepting a single countersunk screw to anchor the assembly before threading the tie.
- Fastener Standard: Countersink fits #6 or #8 flat-head wood screws.
- Tie Clearance: Pass-through slot accepts standard nylon zip ties up to 5mm wide.
- Capacity: Cupped cradle holds wire bundles up to 10mm in diameter.
- Measurement to Check: Verify your outer wire jacket combined diameter does not exceed 10mm; oversized bundles will bridge the cradle and stress the zip tie rather than resting in the saddle.
Photos
Technical views
More like this
Explore more in Home & Fixtures →
Figure8 — Clip-On Cord Winder
Figure8 is a compact cord winder that snaps onto the flex of a kettle, toaster or similar appliance and takes up the slack. Wrap the spare cord around the two end horns in a figure-eight pattern, and the curled horn tips hold the turns in place so the wrapped cord can't spring loose. It is designed for cluttered counters where appliance cords tend to tangle. The spine carries a round channel with a narrower snap-in slot, so the winder stays on the cord instead of sliding off. The cord is pressed through the slot, and the lips flex to let it pass. Dimensions Overall length: 80 mm Overall width: about 46 mm across the horns Height: 9 mm Cord channel: 5 mm diameter, running the full spine Snap-in slot: 4 mm opening Features Four horns with tips curled back toward the centre Chamfered spine edges Single-piece body with no assembly Compatibility Intended for standard 6–7 mm appliance cords, which squeeze through the slot and sit snugly in the channel Print notes PETG or TPU is recommended, since the slot lips need to flex Stiff PLA may crack at the lips when the cord is pushed in Prints flat on the bed; the curled tips are short, so supports are only needed if the slicer flags them
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Cardboard Sign Corner Holder for Wall
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad. Slot height: 3.4 mm for 3 mm cardboard Leg length: 40 mm per corner Back plate: 2 mm, flat side faces the wall Front lip: 1.6 mm, with a cut-out window Print: flat on the back, no supports, one per corner (4 for a sign)
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
Veranda Back Railing Bays
Railing section for the back half of the veranda, made to print separately from the deck base. It covers the long left side and the short end, with pickets running between a lower and a top rail. Left side bay with end post, plus the end-span railing across the back Pickets about every 110 mm at full scale Posts sit flat on the deck surface for gluing Same scale and position as the deck base, so the pieces line up