110×70 mm Himalaya School Visitor Pass
Created today
Description
Two-body visitor pass for Himalaya Public Sr. Sec. School: a white 110 × 70 × 4 mm plate with 3 mm corner radius, and solid dark-blue raised lettering.
Fit and dimensions
- Plate: 110 × 70 × 4 mm, rounded corners.
- Letters: 2 mm proud of the plate, flat bottoms seated on the top face (overall height 6 mm).
- Text: HIMALAYA PUBLIC / SR. SEC. SCHOOL / VISITOR PASS, centred, well inside the 4 mm margin.
Check before printing
Confirm the text stays within 4 mm of every edge in your slicer. Assign the white and blue bodies to separate filaments. There is no hole or lanyard slot.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Raised Star Ornament
A 70 mm five-pointed star ornament designed to print flat on the build plate. It features a smaller raised star and radiating decorative lines on the front face, adding visual interest while remaining easy to print without supports. 70 mm overall width 5 mm integrated hanging hole 2.2 mm base thickness with an additional 0.8 mm raised pattern Flat back for bed adhesion
150mm Bayonet Twist Vault
A 150mm mechanical drop-in vault, built around a 50mm twist-lift track. This replaces the friction fit of the original 150mm Borg Friendship Vault with a proper bayonet mechanism. The outer cage runs three 18mm tall helical tracks to guide the core. The top cap terminates in a 40mm hexagonal drive plug; dropping it onto the core and twisting counter-clockwise forces the payload to lift 50mm out of the chassis. Bore Clearance: The 98mm core runs inside a 102mm cage bore. Verify your machine holds tolerances on large cylinders. Support-Free: The massive 90mm flat bridges of the original have been replaced by mechanical vertical slots with 45-degree angled roofs. No supports needed for the cage or core lugs. Payload Capacity: The hollow inner void measures 76mm in diameter by 110mm deep. To assemble, line up the core lugs with the vertical entry slots on the inner walls of the cage, push down to the top stop, and twist right to lock it securely to the bottom.
Hartvormige fotolijst voor oma
Hartvormige fotolijst ontworpen rondom de standaardafmeting van een 10x15 cm foto. De lijst bevat verhoogde details zoals bloemen, kleine hartjes en de tekst in het Satisfy-lettertype. Omdat reguliere emoji's niet naar gcode vertalen, is het hartje in de tekst vervangen door een massief 3D-element. Constructie en Printen De Sponning: Aan de achterkant zit een uitsparing van exact 104x154 mm. Dit geeft rondom 2 mm speling voor de foto, plus de 3 mm dikke rugplaat. Ondersteuning: Print het hoofdframe plat op zijn rug. Voor de sponning van de foto is in de slicer een beetje "support" (ondersteuning) vereist. Montage: De rugplaat klemt strak in het frame. De losse standaard schuift onder een hoek van 45 graden in de rugplaat. Gebruik eventueel een klein beetje tape of lijm als de frictie van je print niet strak genoeg is.
Bracelet Octobre Rose 78mm
Un bracelet jonc simple et élégant, gravé du texte "OCTOBRE ROSE" en creux pour marquer l'événement sans nécessiter d'impression multicolore. Diamètre intérieur : 78 mm (ajusté pour un enfilage confortable) Épaisseur de paroi : 3 mm Hauteur : 12 mm Gravure : Découpée dans la paroi extérieure Impression : Conçu pour s'imprimer à plat sans aucun support
Snap-Fire — Auto Crossbow
A fully print-in-place auto-reloading mini crossbow. This model is scaled for standard 6mm airsoft BBs and features a gravity hopper that drops the next shot right onto the firing groove every time the string is drawn back. Features Auto-Reload Hopper: Stack 5-6 BBs vertically; pulling the string cycles the next shot. String Guide Tracks: Side rails capture the rubber band on release so it flies perfectly straight without jumping off the barrel. Print-in-Place Trigger: The trigger mechanism prints fully assembled with a built-in pivot pin. Just wiggle it free after printing. String a standard rubber band between the side notches on the front arms and feed it through the guide tracks to shoot.
Wazowski — Hinged Arms, Viper Horns
Wazowski is a set of two hinged monster arms and two horns, made to sew onto a maternity shirt panel. Each arm splits into an upper arm and a forearm with hand, and the horns are slender, backward-curving thorns in the style of a desert horned viper. Features Upper arm with a single lower hinge plate. The top plate is left off so the forearm can be glued in place. Forearm and hand with three fingers and a thumb, plus a short pin that locates in the hinge hole. Two horns, 60 mm tall, tapering to a fine tip with a slight curve. Round flanges with six sewing holes on each arm and horn. Print notes Print the arms in TPU or another flexible filament so they move with fabric. Glue the forearm knuckle onto the hinge plate with the pin seated in the hole. Proportions are set for scaling, so resize in the slicer to fit.