1.7-Inch AFX Slot Car Bus Body
Created 4 months ago
Description
A direct-fit school bus body designed for AFX Mega G+ standard (1.7-inch wheelbase) slot car chassis. It features a boxy cabin, hood geometry, and integrated internal retention rails.
- Scale: HO (~1:64)
- Wheelbase Alignment: 43.2mm (1.7-inch)
- Wall Thickness: 1.5mm shell
- Mounting Interface: Dual internal side rails at 5mm Z-height to register into standard chassis side-clips
- Clearance: Enlarged rear wheel arches accommodate minor wheelbase tolerances
Images
More like this
Explore more in Automotive, RC & Hobby →
Car Coffee Tray shj
A rectangular car coffee tray, 124.7 × 107.4 mm and 10 mm tall, with a raised 4 mm rim and a recessed floor to keep cups and items in place. "meet me in SHJ" is engraved 0.8 mm deep into the floor in the bottom-right corner. Remix hooks Text weight: the letters are 7 mm tall with strokes thickened by 0.3 mm per side. Raise that for a bolder engraving, or drop it to return to the plain font weight. Text size and position: 7 mm size, 5 mm in from the rim. Change the inset to move it, or switch the alignment to centre it. Rim and floor: 4 mm wall and 4 mm floor thickness. A taller rim holds more, a thinner floor saves filament. Pairs with: a non-slip mat under the base, or a cup-sized ring added to the floor.
Ajman car tray
A rectangular coffee tray for the car, measuring 124.7 mm wide by 107.4 mm deep, with a raised rim and a recessed inner surface that keeps cups and items in place. "Meet me in Ajman" is engraved into the inner floor, centered. 124.7 × 107.4 mm footprint, 10 mm tall 4 mm raised walls with rounded corners Recessed floor, 6 mm below the rim Text engraved 1 mm deep, not raised Flat bottom, single solid piece, no supports needed
RC Car Bevel Gear Rear Drive
A rear-axle drive for an RC car where the motor shaft has to turn 90° into a cross-car axle without the gears skipping or the motor shifting. This set uses a 12-tooth pinion and 24-tooth crown gear (2:1) on a 103.9 mm × 6 mm axle, with an open motor cradle instead of a closed box. Key numbers Gears: module 1.5, 20° pressure angle, 4 mm face width, 90° shaft angle Pitch cone angles: 26.57° (pinion) and 63.43° (crown); cone distance about 20.1 mm Pinion bore 2.1 mm, crown bore 6.2 mm, both with M3 set-screw holes in the hubs Axle supports: 6.4 mm through-hole plus a 17.3 mm seat for 606 bearings (6×17×6) Base: 84 × 92 × 5 mm, M3 holes (3.4 mm clearance); cradle slots allow forward and back adjustment Motor cradle parameters at the top of the file: mw, mh, wall, saddlel, saddley. Measure the real motor and edit them Cover is open at the bottom, with two M3 ears at the rear Printing Print gears with the hub facing up or down on the bed; PETG or nylon preferred Cover prints open-side up without supports Axle is a separate 6 mm steel rod; M3 screws hold supports, cradle, straps and cover
25mm Tactical Tabletop Tokens
A complete set of nine 25mm wargaming tokens tailored for tabletop tracking. Designed with a clear separation between the base and the raised lettering, making them perfectly suited for a mid-print filament swap or a multi-material system. Specifications Dimensions: 25 mm diameter, 4 mm overall height. Tolerances: The raised text and outer rim sit exactly 1 mm above the base layer, creating a clean Z-height transition for color changes. Printability: No supports required. The bottom edges feature a 1 mm chamfer to prevent elephant-foot distortion on the first layer, ensuring the tokens remain perfectly circular and easy to pick up from flat tables. Layout: Arranged in a flat 3x3 grid for immediate batch printing. Can be split into individual models in the slicer if needed.
Curved Snap-In Interior Trim Cover
A 123 × 180 mm curved interior trim cover with a straight bottom edge, a stepped outline (107 mm wide at the top, 123 mm in the lower 85 mm) and a 3 mm panel. The perimeter flange follows the crowned surface so the part sits flush around the opening. Remix hooks Surface crown: the front curvature is a few millimetres in both directions. Flatten or deepen it to match a measured body profile. Raised area: 10 mm high with a soft ~30 mm blend at the upper left. Change height or width to suit. Clips: five per side at 18, 54, 90, 126 and 162 mm, 14 mm wide and 4.5 mm thick, with a ~2 mm hook. Adjust hook depth to the real metal edge thickness. Rear frame: 15 mm deep, 2.8 mm wall, inset 3.5 mm. Change the inset for a tighter or looser fit. Pairs with: fuzzy skin in the slicer for a textured look. Print in PETG, ASA or ABS.
OO Gauge semi detached house stone v2
A semi-detached stone house pair in OO gauge, printed as separate pieces: front wall with quoins at the outer ends, mitred side walls, a one-piece roof, a floor piece, two chimneys, and separate window and door inserts. Four small locator rails now help position the side-wall tabs on the front wall. Remix hooks Tab locators: four U-shaped pieces, each 6.8 × 18.6 × 1.5 mm. Glue one against the inside of the front wall beside each side-wall tab. The 0.3 mm clearance around the 15 × 5 mm tab is the value to tune for your printer. Locator thickness: 1.5 mm now. Raise it for a firmer stop. Window and door inserts: 3 mm thick, 0.2 mm clearance per side. Pairs well with: a thin plasticard base or a printed street baseboard.