200mm 3-Compartment Box Base
Created 1 months ago
Description
The base section of a 200mm square storage box equipped with three equal front-to-back compartments. Isolated for direct printing on 220x220mm beds like the Creality K1C.
What it fits
Sorting and protecting mid-sized tools, hardware, or craft supplies. Mates with the matching 205mm drop-on lid.
Dimensions to check
- Base outer: 200 x 200 x 50 mm
- Compartments: Three slots, each 64 x 196 x 48 mm internally
- Wall thickness: 2 mm universally
Photos
Technical views
More like this
Explore more in Storage & Organization →
Large Cable Organizer Box
A high-capacity cable management box with a fitted drop-in lid, sized to house bulky power strips, large transformers, and excess cable coils. The rear panel features two mouse-hole style arch cutouts seated flush with the interior floor for easy drop-in cable routing without requiring cables to be threaded through tight slots. What it's for Concealing power strips, power bricks, and cable runs on desktops or floors Floor-level cable pass-through that keeps cords flat against the surface Dust protection with an easy-access lift-off lid Dimensions Internal Clearance: 215.9 mm (8.5") W × 292.1 mm (11.5") D × 127.0 mm (5.0") H Wall Thickness: 3.0 mm Port Size: 40 mm wide × 64 mm high arched openings flush to the floor plate Outer Footprint: 221.9 mm × 298.1 mm × 133.0 mm (excluding lid hover offset) Print notes Print the box base-down with no supports needed for the arched ports. The lid prints flat on its top face for maximum surface quality and bed adhesion. Requires a build volume of at least 300 mm × 225 mm.
Tiny Lidded Storage Box
What it's for A miniature storage box with a slip-fit lid, perfectly sized for keeping tiny components, screws, or small parts securely contained. Dimensions Outer: 1.25" × 1.75" × 0.625" (31.75 × 44.45 × 15.87 mm) Wall thickness: 1.5 mm Lid clearance: 0.2 mm per side for a snug but easy-to-remove fit Assembly The lid prints completely separately alongside the main body. The small inner lip locates cleanly inside the box opening.
Cable organizer box with Unifi AP Lid
Our coworking space needs some cables organized on top of the kitchen cabinets. V1, not tested yet, so print at your own risk!
Split 13-Inch Slip Box
A simple, cleanly split rectangular enclosure meeting a 3" × 1" × 13" outer footprint. Designed to print standing vertically on the build plate, the two halves meet in the middle with a sliding half-lap joint that handles alignment and friction. Remix Hooks The source relies on a few key parameters that dictate the fit and feel. If you pull this into a remix, check these first: Dimensions: Currently W = 76.2, D = 25.4, and L = 172.6 (for each half, achieving the 330.2mm total length). Tweak these to fit whatever board or gear you are housing. Wall: Set to 3mm. This gives enough meat for the half-lap cut (leaving 1.5mm walls at the joint) without feeling overly bulky. Clearance: The joint runs a comfortable 0.4mm tolerance. Tighten it to 0.2mm if your printer is dialed in and you want a semi-permanent friction fit, or loosen it if it binds. Lip Length: The 15mm overlap keeps the assembled box rigid, but dropping it to 8-10mm would save a bit of plastic if the contents don't flex.
Trinket Box With Captive Hinge
Most 3D-printed boxes rely on thin plastic living hinges that fatigue and snap off after a week of use, or require separate filament fragments as pins that eventually back out. This print-in-place trinket box uses a five-knuckle mechanical barrel hinge with integrated teardrop pins to prevent bridging collapse. A front thumb-tab with an offset detent provides a positive snap closure so the lid doesn't flap open when jostled in a drawer. Dimensions: 70 mm x 50 mm x 30 mm overall footprint. Walls: 2 mm solid perimeters for rigidity. Tolerances: 0.4 mm clearance inside the hinge barrel to prevent the knuckles from fusing during extrusion. Printing: Print fully closed, flat on the base. Requires no supports.
Asymmetric 16-Slot Makeup Organizer
A single-piece makeup and vanity organizer built to the specified 200x140x90mm volume. The layout uses an asymmetric stepped profile to match compartment depths to their contents while maintaining a clean, minimalist silhouette. All interior vertical edges feature a 3mm radius to prevent powder buildup, and the outer shell carries an 8mm continuous radius. Specifications Dimensions: 200mm (W) × 140mm (D) × 90mm (H) overall. Brush Storage: Two rear compartments (90mm deep) sized for long-handled tools. Creams & Perfume: Twin mid-tier compartments (60mm deep) accommodating standard jars and bottles. Lipstick Grid: 16 independent 21.5mm square slots arranged in a 4×4 matrix (45mm deep). Jewelry Tray: Shallow front-left basin (30mm deep) for rings and small items. Printability: 2.4mm uniform wall and floor thickness. Prints flat without supports.