22mm Shower Bracket Replacement Cup
Created 1 months ago
Description
What it's for
A functional structural replacement for perished rubber friction cups commonly found in standard hand shower brackets. Instead of relying on a completely flexible rubber body, this cup utilizes four printed internal ridges to create a secure friction fit against a standard 22mm shower head ball end.
Dimensions
- Inner Diameter: 22.5mm
- Internal Depth: 30.0mm
- Outer Diameter: 27.5mm
- Overall Height: 32.5mm
- Wall & Base Thickness: 2.5mm
Materials
Because this part is exposed to continuous heat, moisture, and mechanical stress, PETG, ABS, or a rigid TPU (like 95A) are highly recommended. PLA may soften or deform under hot water temperatures.
Remix ideas
- Bracket sizing: Adjust the primary outer diameter and wall thickness to match the cavity of your specific wall-mounted bracket housing.
- Mounting holes: Add a central clearance hole or countersink to the base if the original cup was secured with a screw.
- Friction tweaking: Alter the radius of the four internal ridges to tune the grip strength on the 22mm shower head.
Photos
Technical views
More like this
Explore more in Home & Fixtures →
Tower Fan Bearing Bracket
What it's for A custom replacement L-bracket designed to hold a 626ZZ ball bearing at the top of a cross-flow fan rotor in a tower unit. Built to secure the 6mm fan shaft while maintaining precise wall clearance. Dimensions Arm Dimensions: 54mm x 44mm footprint, 5mm thick. Wall Face: 18mm total height. Mounting: Two 4mm screw holes, spaced 28mm apart horizontally and centered at 14mm from the base (4mm from the top of the wall face). Bearing Seat: Sized for a 19mm OD bearing, dropped 3mm below the main flat surface, featuring an open top for drop-in installation and a 12mm clearance hole below for easy push-out removal. Print notes Because the bearing housing now protrudes 3mm past the bottom of the main arm, the model is lifted so the lowest point rests on the print bed. You will need to enable supports under the flat arm, or rotate the part manually in your slicer if you prefer a different print orientation.
Angled-Entry Tomato Vine Clips
A set of dual-loop clips designed to secure growing tomato vines to standard 1cm bamboo stakes. The vine loop features a 45-degree angled entry slot, allowing stems to be guided in without threading or bending delicate tips, while the generous internal diameter leaves room for the stem to thicken over the season. Remix Hooks Stake Bore: Currently set to a 10mm inner diameter with a 6.5mm snap gap. Adjust this to match 8mm or 12mm garden stakes. Vine Capacity: The vine loop sits at 15mm ID to accommodate mature tomato stems. Scale this up for heavy-set cultivars or down for peppers and beans. Entry Angle: The 6mm vine slot is positioned at 45 degrees to prevent accidental slip-outs. Adjust the angle or narrow the gap for vines that need a tighter capture. Thickness: Extruded to 8mm, giving the stake loop enough surface area to grip securely when printed in PETG or PLA.
bird bath shower head 5/16" 2
A friction-fit spray nozzle designed to convert a standard 5/16" ID water line into a wide, gentle shower for a bird bath or fountain. The part is modelled upside down (spray face flat on the Z-plane) so it prints cleanly as a single hollow body without any internal or external supports. Parameters to Play With If you take this into your own setup, here are the numbers driving the shape: The Stem Fit: Tapers from 8.5mm down to 7.2mm over a 20mm length. This is the sweet spot to wedge tightly into soft 5/16" (7.94mm) tubing without blowing out under mild pump pressure. The Spray Face: A 45mm outer diameter with a flat 2mm-thick face plate. The Holes: Uses a grid of 1.5mm holes spaced 3.5mm apart. Remix Hooks Flow Rate: If your pump is struggling to push water through, widen the internal 4.5mm bore or bump the face holes from 1.5mm up to 2.5mm. Directional Spray: Instead of a full grid of holes, mask off half the face to create a directional fan spray. Barbs: The smooth taper seals well for low pressure, but if you're running higher pressure, swapping the smooth cone for a stepped barbed profile will lock the tubing down harder.
Brusali Pivot Repair Bracket
A low-profile repair bracket designed to replace a torn-out pivot pin (part 112792) in an Ikea BRUSALI shoe cabinet. Bridges damaged particleboard to anchor firmly into intact wood. Remix Hooks Baseplate Size: Currently a 60x60mm footprint to reach past standard blowout damage. Expand it if the tear is wider. Plate Thickness: Sitting at 3mm to keep clearance tight. Scalloped edges halve that thickness between the screws to save material without compromising the direct stress paths to the corners. Pivot Pin: Set to 14.5mm diameter and 10mm length. Double-check your surviving hardware — you can easily dial the diameter up or down to tune the friction fit into the drawer groove.
Low-Profile Pool Siphon Pickup
The garden hose floats, the pool floor is bare, and the last half-inch of water refuses to drain. You prop the hose with a brick, it slips, the siphon breaks, and you start over. This unified pickup drops onto the pool floor and forces the siphon to pull from a continuous 3mm gap right at the base. The hollow internal plenum distributes suction evenly, while bottom grooves stop the plate from vacuum-sealing itself to the liner. Print Strategy Dimensions: 128 × 128 × 11.5 mm (excluding standard 3/4" GHT thread). Bridging: The internal chamber is packed with a 16mm grid of support pillars and a solid center ledge. The roof spans those gaps perfectly flat without slicer supports. Material: PETG or ASA recommended to survive the sun and pool chemicals. Use dense infill so it sinks.
Garage Vent to 6-Inch Adapter
A custom 2-part venting adapter designed to connect a 360x210mm drywall vent gap to a standard 6-inch exhaust duct. Two-Part Assembly: Splits perfectly down the middle with a 10mm external flat flange for easy gluing. Tapered Male Fitting: Connects securely inside standard 6-inch ducting. Support-Free Print: Internal lofts are designed to print cleanly with no supports while encouraging laminar exhaust flow. Mounting Integration: Six #6 screw holes for securing to drywall, with an extended bottom footing to rest cleanly on a garage concrete foundation.