30-Degree Macro Pad Stand
Created 3 months ago
Description
A tilted desktop stand designed to change the resting angle of a flat macro keypad. Pitching the keypad at an angle brings the keys into a direct sightline, reducing mis-hits and accidental presses during active use. The cradle wraps the base of the device to secure it, preventing the pad from creeping backward across the desk as pressure is applied to the keys.
Key features and dimensions:
- Fits macro pads measuring up to 118x84mm (includes 1mm of functional clearance).
- Fixed 30-degree working angle.
- Rear 25mm cutout accommodates central cable routing.
- Hollowed wedge structure minimizes printing material while maintaining a stable support footprint.
Photos
Technical views
More like this
Explore more in Desk & Tech →
Foldable Snap-Fit Phone Stand
A rugged, fully printable foldable phone stand. It is printed in three flat pieces that snap together securely, allowing it to fold completely flat for travel. Features Adjustable Angles: Features 7 resting notches on the base plate to precisely control the screen angle. Snap-Fit Hinges: Uses C-clip snap joints that grip firmly onto 6mm pins without requiring any extra hardware. Travel-Ready: Folds down to a flat profile when not in use. Print Instructions Print flat on the bed as oriented. Standard PLA or PETG works perfectly. Ensure good bed adhesion for the flat plates. The snap-fit hinges are designed with a 0.4mm clearance — they will require a firm push to snap into place during assembly, but will hold tight thereafter.
Phone Stand with Cable Channel
A phone stand that holds the phone upright in portrait or landscape, with a cable channel so the charger doesn't pin the phone down or dangle off the edge. Most stands either tip the phone back too far to tap or force the cable to loop around the outside. This one leans the phone at 70° from horizontal and routes the cable up through the stand to the back of the phone. What decides fit and print Lean angle: 70° from horizontal, steep enough to tap the screen and upright enough to watch video. Groove: runs the full 90 mm width, so the phone sits in it in either orientation. It is sized for a phone in a thin case. Cable channel: 12 mm wide, open on the underside of the base. It runs in from the back, then rises through a 12 x 12 mm opening in the groove floor. Overall size: 90 mm wide, about 56 mm deep and 70 mm tall. Printing: the flat base goes down on the bed. The underside channel is a 7 mm-tall tunnel, so print it with bridging on or light supports. No other supports are needed. Material: PLA or PETG both work. Use 3 or more perimeters for a stiffer groove lip.
StudyDock Desktop Phone Stand
What it's for A one-piece desktop phone stand for students, holding a phone at a 65° viewing angle on a desk. Dimensions 65 mm wide, 75 mm deep, 70 mm tall 4 mm flat base, 4–5 mm walls 14 mm deep shelf with a 6 mm front lip Two triangular side supports Remix ideas Widen the shelf for phones with cases. Add a cable slot through the backrest. Lower the backrest angle for typing-height viewing.
Snake Tail Phone Stand
A one-piece orange phone stand with a low front lip, a short flat seat and a backrest leaning up to about 60 mm. A zig-zag snake of humps runs along the back. Remix hooks Lip height: the front stopper is about 5 mm of strip plus the strip's rounded end, roughly 7.5 mm in total. Raise it for a more secure hold, or lower it further to keep captions clear. Seat depth: 12 mm. Deepen it for thick cases, though a steeper backrest helps more. Backrest angle and height: it rises about 18 mm in Y over 55 mm in Z, so it is steep. Both are easy to change. Snake humps: 4 peaks, each about 14 mm high. Add more humps, or raise or lower the peaks. Width: 70 mm, with a 5 mm strip thickness. Pairs well with a non-slip pad on the seat.
Cartoon Cloud MagSafe Stand
A heavy, volumetric desktop stand for the iPhone 15 with a friction-fit MagSafe socket. The body is built as a fully rounded, bubbling cloud with a perfectly sheared flat front to carry the phone and a sliced flat bottom for desk stability. Mounted on a heavy, hidden pill base holding a 20-degree back-tilt. Fit: 56.5 mm cutout for a standard MagSafe puck, with an 8 mm channel for the cable routing down the face. Format: Two-piece assembly. The cloud and the base print separately and socket together. Volume: Bubbly 3D geometry across the back and sides; dead flat front surface for phone rest.
Monitor stand v2
A one-piece stand for a 200 × 110 × 18 mm tablet, holding it at 70° from horizontal. Two angled supports are joined by a solid crossbar, with a front lip and a backrest. Fitment Supports are 20 mm wide, centred 100 mm apart, so they land at 50 mm and 150 mm along the tablet's 200 mm width. Overall stand width is 120 mm; the tablet overhangs 40 mm each side. Slot depth is 20.5 mm for an 18 mm tablet. Front lip covers only the bezel. Check before printing Measure the tablet's thickness with any case on. Anything over about 20 mm will not enter the slot. Does not fit Tablets thicker than 20 mm, or portrait-orientation use, which this stand is not shaped for.