4.5mm USB-C Desk Anchor
Created 1 months ago
Description
An adhesive-mount anchor for securing 4.5mm USB-C cables to the side of a desk. It holds the line captive when unplugged, preventing it from sliding onto the floor under its own weight.
Fitment and Clearances
- Host capacity: Standard 4.5mm rubber and braided USB-C jackets.
- Entry bore: 4.5mm diameter.
- Snap channel: 3mm entry width.
- Mounting interface: 14x14mm flat footprint for standard double-sided tape.
Check Before Printing Measure your cable jacket with calipers. Thick reinforced lines exceeding 4.8mm will bind or crush in the bore. Thin peripheral cords under 3.5mm may slip out of the keyhole opening when the line goes slack.
Images
More like this
Explore more in Desk & Tech →
Foldable Snap-Fit Phone Stand
A rugged, fully printable foldable phone stand. It is printed in three flat pieces that snap together securely, allowing it to fold completely flat for travel. Features Adjustable Angles: Features 7 resting notches on the base plate to precisely control the screen angle. Snap-Fit Hinges: Uses C-clip snap joints that grip firmly onto 6mm pins without requiring any extra hardware. Travel-Ready: Folds down to a flat profile when not in use. Print Instructions Print flat on the bed as oriented. Standard PLA or PETG works perfectly. Ensure good bed adhesion for the flat plates. The snap-fit hinges are designed with a 0.4mm clearance — they will require a firm push to snap into place during assembly, but will hold tight thereafter.
Phone Stand with Cable Channel
A phone stand that holds the phone upright in portrait or landscape, with a cable channel so the charger doesn't pin the phone down or dangle off the edge. Most stands either tip the phone back too far to tap or force the cable to loop around the outside. This one leans the phone at 70° from horizontal and routes the cable up through the stand to the back of the phone. What decides fit and print Lean angle: 70° from horizontal, steep enough to tap the screen and upright enough to watch video. Groove: runs the full 90 mm width, so the phone sits in it in either orientation. It is sized for a phone in a thin case. Cable channel: 12 mm wide, open on the underside of the base. It runs in from the back, then rises through a 12 x 12 mm opening in the groove floor. Overall size: 90 mm wide, about 56 mm deep and 70 mm tall. Printing: the flat base goes down on the bed. The underside channel is a 7 mm-tall tunnel, so print it with bridging on or light supports. No other supports are needed. Material: PLA or PETG both work. Use 3 or more perimeters for a stiffer groove lip.
Organischer Kopfhörerständer in Rosa
Kopfhörerständer mit breitem, abgerundetem Bogen, geschwungenen, sich kreuzenden Streben und einer flachen, wellenförmigen Standfläche. Ein zusammenhängender Körper, flach druckbar, gedacht für pastellrosa PLA. Remix-Ansatz Bogen: Außenradius 65 mm, Strebenbreite 22 mm. Größerer Radius für breitere Kopfbügel. Streben: Vier Kurven, Kontrollpunkte frei verschiebbar für andere Öffnungen. Basis: ca. 224 × 150 mm, 8 mm hoch. Dicker oder mit Gewicht-Einlage für mehr Standsicherheit. Tiefe der Streben: 36 mm, anpassbar. Gesamthöhe ca. 260 mm.
Arcade Console Desk Clock Case
A compact desk-clock enclosure with a gaming-rig attitude: chamfered shoulders, vented flanks and grooved front stripes under the OLED window, like a mini console from a late-night LAN party. Window for a 0.96" OLED on the front Standoffs for an ESP32 WROOM-32 devkit USB slot at the back Four corner screw bosses and a separate screw-on lid Side vent slots for airflow
Ten-Port Keystone Panel With Fan
A 270 × 61 mm mounting panel with a 60 mm fan opening on the left and ten snap-in keystone ports on the right. A rounded, squircle-style notch is cut into one long edge near the right end. Remix hooks Notch span: runs from 216.25 mm to 258 mm along X, 15.25 mm deep in Y. Move either end to resize it. Corner radius: both inner corners use a 7 mm radius. Raise it for a softer shape; keep it under about 7.6 mm to stay within the notch depth. Corner material: the notch stops at 258 mm, leaving the right-end 3.5 mm mounting hole (5 mm from the end) fully surrounded. Keystones: 14.5 × 16 mm openings with a 1.8 mm front lip and rear clip relief. Dimensions are provisional, so test one jack before printing all ten. Pairs with: a cable-management bar or a fan grille over the 58 mm vent. It's meant for a particular 12U rack.
StudyDock Desktop Phone Stand
What it's for A one-piece desktop phone stand for students, holding a phone at a 65° viewing angle on a desk. Dimensions 65 mm wide, 75 mm deep, 70 mm tall 4 mm flat base, 4–5 mm walls 14 mm deep shelf with a 6 mm front lip Two triangular side supports Remix ideas Widen the shelf for phones with cases. Add a cable slot through the backrest. Lower the backrest angle for typing-height viewing.