69 mm Round Spacer, 5 Holes
Created today
Description
A round spacer 69 mm in diameter and 10 mm tall with a 40 mm center bore and five 5.5 mm through-holes on a 54 mm bolt circle.
- Outer diameter: 69 mm
- Height: 10 mm
- Center hole: 40 mm
- Bolt holes: 5 × 5.5 mm on a 54 mm circle
- Hole spacing: 68°, 72°, 72°, 68°, 80° (the 80° gap is between the last and first hole)
- Prints flat with no supports
Images
More like this
Explore more in Workshop & Tools →
outside hat
A plain flat disc in the spirit of an oversized washer or a vinyl-record blank: 3 inches across, 1/8 inch thick, with a clean 1 cm hole through the centre. Prints flat with no supports. Diameter: 76.2 mm (3 in) Thickness: 3.175 mm (1/8 in) Centre hole: 10 mm Good for spacers, coasters, templates, or as a base for other builds
door lock
Rectangular block, 100 mm long, 24 mm wide and 15 mm tall, with a 16 mm wide by 11 mm deep groove running the full length along the top centre. The groove size is engraved into the groove floor as "16 x 11 mm". Overall size: 100 x 24 x 15 mm Groove: 16 mm wide x 11 mm deep, open at both ends Side walls: 4 mm; floor: 4 mm Engraving: 0.6 mm deep, readable from above Prints flat with no supports
5-Way Flat H-Manifold
What it's for A flat pneumatic or fluid splitter featuring five branches. Arranged in an H-configuration with an additional trailing branch, keeping the entire assembly planar for simple routing and straightforward printing. Dimensions Branch outer diameter: 10 mm Branch inner diameter: 7 mm (1.5 mm walls) Overall length: 50 mm (from the closed cap to the tail tip) Overall width: 40 mm (across the parallel arms) Spacing: 25 mm between the two cross sections Print notes Lays entirely flat on the print bed. The horizontal pipes print safely without supports on most standard FDM setups.
Klipper Display and Status Console
Compact left-side mounting enclosure for Klipper printer telemetry, designed specifically for the Ender 3 Pro 2040 vertical extrusion. Hardware Compatibility: Fits a 1602A I2C LCD, a 32x32mm HW-109 MAX7219 LED Matrix, and a standard 5mm RGB LED. Internal Clearance: 36mm cavity depth cleanly clears standard I2C backpacks. Mounting System: Left-oriented 5mm side flange using dual slots for M4 t-nuts. Flange sits flush to the bottom, leaving top clearance for gantry travel. Assembly: Snap-fit 2mm front panel with internal screw bosses; back plate secured via four M3 interior corners. The housing prioritises rigidity and short wiring paths over bulk, anchoring firmly without compromising structural frame limits.
Zauberstab 3.5
What it's for Zweiteiliger Zauberstab mit Griff und Spitze für eine UV-Taschenlampe. Außen ist ein glatter Stab mit schmalen, aufgelegten Teigsträngen, die sich spiralförmig um ihn winden. Innen verschließt ein Bajonett mit Rastnocke. Dimensions Griff: 87 mm hoch, 85 mm Innenhöhe, Bohrung Ø 21,8 mm Spitze: 135 mm gesamt, verjüngt sich nach oben, Lichtkanal innen hohl Glatter Kern Ø 26,4 mm, vier Stränge, ca. 0,8 mm breit am Boden und nach oben schmaler Vier Löcher Ø 3,75 mm im Boden Remix ideas Mehr oder weniger Stränge Stränge dicker für stärkeres Relief Andere Windungszahl über die Höhe
Custom Hex Standoff Tube
Off-the-shelf hardware never matches the exact gap, leaving assemblies rattling or crushed. This custom hex standoff fills the exact space needed while keeping the internal bore clear for a rod or bolt to pass through. Dimensions Height: 55.0 mm (5.5 cm) Outer Profile: 5.15 mm point-to-point hexagon Inner Bore: 2.50 mm diameter