A Hat For My Cat
Created 5 months ago
Description
This is a lovingly crafter hat for my cat, complete with tie down holes for beautiful red ribbon for my smoochypoos neck to make sure her lovely hat stays on!
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament
Wazowski — Hinged Arms, Viper Horns
Wazowski is a set of two hinged monster arms and two horns, made to sew onto a maternity shirt panel. Each arm splits into an upper arm and a forearm with hand, and the horns are slender, backward-curving thorns in the style of a desert horned viper. Features Upper arm with a single lower hinge plate. The top plate is left off so the forearm can be glued in place. Forearm and hand with three fingers and a thumb, plus a short pin that locates in the hinge hole. Two horns, 60 mm tall, tapering to a fine tip with a slight curve. Round flanges with six sewing holes on each arm and horn. Print notes Print the arms in TPU or another flexible filament so they move with fabric. Glue the forearm knuckle onto the hinge plate with the pin seated in the hole. Proportions are set for scaling, so resize in the slicer to fit.
Yoshi Saddle Shell Backpack Mount
A red Yoshi-style shell dome on a white base plate that straps onto a backpack. What it's for Turns a backpack into a Yoshi costume piece. Webbing passes through four slots in the base plate, so the shell sits on the backpack's outer face. Dimensions Overall: about 214 × 175 × 94 mm, fits a 256 mm bed in one piece Dome wall: about 4 mm, hollow underneath Base plate: 6 mm thick Strap slots: four, each 44 × 7 mm, at X ±60, Y ±32 Remix ideas Add white spots or a ridge band on the dome Widen the slots for thicker webbing Add a foam pad under the base plate
Curved Halloween Horn for "Power"
A hollow, gently curved cone horn with an open base, sized for Halloween costumes. Base diameter is 40 mm, height 60 mm, with the tip leaning 25 mm to one side and a 2.5 mm wall. Remix hooks Base diameter (D = 40 mm): widen for a headband mount, narrow for a hairclip or small hat. Bend (25 mm): lower for a straighter horn; higher gives a hook-like sweep, but needs more support when printed upright. Wall (2.5 mm): thin it to save filament, thicken for durability. Height (60 mm): stretch for a taller, more dramatic horn. Pairs with A mirrored copy for a matching left and right set. A headband, a hat, or a printed base ring with a slot for mounting.
Starfleet Communicator Halloween Prop
A handheld communicator prop in the spirit of classic Star Trek, sized to carry or clip to a costume belt. It is a 90 × 36 × 12 mm slab with rounded corners, a slotted speaker grille, a round dial and a raised gold-style delta emblem. Remix hooks Body size: 90 × 36 × 12 mm. Scale length for a chunkier prop or shrink it for a pocket version. Grille slots: nine slots at 4 mm spacing. Change the count or width for a different look. Emblem: the delta is a simple 4-point polygon. Swap in a different insignia or text. Dial: 10 mm round knob. Make it a button, or add a hole for a small LED. Pairs with: a belt clip, a keyring loop on the back, or a hinged lid to make it a true flip communicator. Printing: print the parts in silver, gold and blue, or paint after printing.
Hartvormige fotolijst voor oma
Hartvormige fotolijst ontworpen rondom de standaardafmeting van een 10x15 cm foto. De lijst bevat verhoogde details zoals bloemen, kleine hartjes en de tekst in het Satisfy-lettertype. Omdat reguliere emoji's niet naar gcode vertalen, is het hartje in de tekst vervangen door een massief 3D-element. Constructie en Printen De Sponning: Aan de achterkant zit een uitsparing van exact 104x154 mm. Dit geeft rondom 2 mm speling voor de foto, plus de 3 mm dikke rugplaat. Ondersteuning: Print het hoofdframe plat op zijn rug. Voor de sponning van de foto is in de slicer een beetje "support" (ondersteuning) vereist. Montage: De rugplaat klemt strak in het frame. De losse standaard schuift onder een hoek van 45 graden in de rugplaat. Gebruik eventueel een klein beetje tape of lijm als de frictie van je print niet strak genoeg is.