Advent Calendar Drawer With Grip
Created today
Description
A single replacement drawer for an Advent calendar: open-top box, 41.5 × 23.5 × 44 mm, 1.5 mm walls and floor, with the number engraved on the front above a small square grip.
Remix hooks
- Grip size: 8 × 5 mm face, 4 mm projection (5 mm deep body, 1 mm embedded). Make it wider for easier pulling.
- Grip rounding: 0.8 mm edge rounding. Raise it for a softer look, drop it for a sharper square.
- Number: 8 mm Roboto, engraved 1 mm deep near the top. Change the digit for other drawers.
- Fit: trim 0.2 mm off width and height if it binds in the frame.
- Pairs with: the other numbered drawers, since the front footprint is unchanged.
Images
More like this
Explore more in Home & Fixtures →
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Veil — Air Freshener Front Plate
Veil is a plain, flat front cover for an automatic air freshener dispenser. It is a clean blank with rounded corners, ready to be used as-is or modified with cutouts for a nozzle, sensor or window. Dimensions Height: 230 mm Width: 76 mm Thickness: 1 mm Corner radius: 8 mm Print notes Print flat on the bed, no supports needed. At 1 mm thick, a wide brim or a slow first layer helps prevent warping.
Lifebuoy — Wall Key Rack
Lifebuoy is a wall-mounted key rack shaped like a beach lifeguard buoy, with a red body, white LIFEGUARD lettering and five sturdy hooks. Features 230 mm long stadium-shaped body, 70 mm tall, 14 mm deep Letters as a separate white piece set into a pocket in the red body Five round-tipped hooks along the lower front Two rear keyhole-style screw holes with counterbores Flat back for printing without supports Print notes Print the body and the letters in separate colours (PLA, 0.4 mm nozzle), back face down.
Wavy Bobby-Pin Sock Clip
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece. Remix hooks Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin. Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more. Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks. Hook radius: 15 mm. Enlarge it for thicker rack rails. Pairs well with a mesh laundry bag. The clip section is 70 mm long and about 15 mm wide. The hook sits above that.
HexGrip — Square-Cut Plywood Hex Clips
HexGrip is a two-clip press-fit system for building hexagonal shelving from 1/2 in plywood, now designed for plain 90° square-cut panel ends. Each slot ends in a solid stop 5 mm from the vertex centre, so neighbouring panels meet at 120° without colliding and no mitre cuts are needed. Features End Cap Clip: two slots at 120° for outer hexagon corners. Spoke Clip: three slots 120° apart for shared vertices in a hexagon network. Barbed slot walls with about 0.55 mm interference per side: ramped entry, steep faces that resist pull-out. Dimensions Slot width 13.0 mm, depth 19 mm Clip height 24 mm, arm length 30 mm Print notes Prints with the slot opening facing up, no supports needed. A single hexagon uses 12 clips, one on the front and one on the back of each vertex. Print one first to check the fit against your actual plywood thickness.