Aerocord — Wire Heart Frame
Created today
Description
A smooth, continuous 10mm tubular loop mathematically traced into a classic heart shape, scaled to a full 20cm span. Ideal as a minimalist wall piece, a wreath frame, or a standalone desk feature.
Dimensions
- Width: 200 mm
- Cord Diameter: 10 mm
- Overall Profile: Sits flat with a 10 mm Z-height
Features
- Continuous Sweep: A closed tubular loop with no hard joints.
- Classic Proportions: Driven by standard parametric heart equations for a familiar, balanced shape.
- Ready to Print: Sits perfectly flat on the bed, requiring zero supports.
Images
More like this
Explore more in Decor & Display →
iPad Picture Frame Adapter Rödlam 21x30
A two-part adapter plate that centers a 5th Generation iPad (9.7") inside an IKEA RÖDALM frame. It acts as a solid backing spacer, locking the tablet into the frame body while providing a cutout exactly the size of the active screen. The split design fits on a standard 220mm print bed and joins with simple flat printed tabs, avoiding overhangs entirely. Remixing and Adjustments Screen Cutout: Currently set to 197 × 148 mm. If you swap to an iPad with a different bezel ratio, you can adjust these dimensions to crop it cleanly. Frame Depth: The total block depth is 30 mm. Thinner frames will require cutting down the outer block height. Cable Routing: A 16 × 25 mm rear channel provides plenty of clearance for bulky aftermarket Lightning cables. Joints: Uses simple 11 × 14 mm rectangular biscuits. You can easily scale these or add more pairs for extra rigidity depending on your printer's tolerances.
Helix — Open-Frame Twisted Fin Lamp Shade
Helix is a flared lamp shade with no solid wall. 72 thin fins spiral through a 60° twist as the shade widens from the base to the top, and three low reinforcing rings hold the whole frame together. The result reads like a lantern or woven cage, and the light comes through as spiralling slats of shadow. The fins and rings are matched on purpose: each fin reaches inward only as far as the rings do, so the inner edge stays clean from bottom to top. A small spoked fitter ring at the base seats the shade over a lamp holder. Dimensions Height: 130 mm Base diameter: about 90 mm Top diameter: about 140 mm Twist: 60° over the full height Features 72 twisted, flared fins, 1.2 mm thick Three low-profile rings at the bottom, middle and top, 3.5 mm tall Fin depth matched to the ring depth (about 6.6 mm at the base, scaling with the flare) Spoked fitter ring at the base, 3 mm tall Print notes Print upright with the fitter ring on the plate. Slow speeds help, since the fins are thin. Use a cool LED bulb only. Fit to a specific socket is untested, so check the fitter ring against your holder.
Flat-Print A4 Picture Frame
A clean, single-piece A4 picture frame designed to print flat on large beds (like 360x360mm). It prints face-down to ensure a smooth front finish and requires zero supports. Integrated Keyholes: Built-in flush mounts for both portrait and landscape orientation. Drop-in Retainers: Six small twist-clips print alongside the frame in the empty center space. They drop into the pre-drilled holes on the back to lock your paper and cardboard backing firmly in place. Generous Recess: The back channel allows up to 2.5mm of clearance, leaving plenty of room for standard A4 paper paired with a corrugated cardboard or stiff card backing.
FLAGE MAROCAINE
A precisely dimensioned 180x120mm base for a Moroccan flag assembly. The model features an accurate 1mm-deep recess carved as five intersecting straight lines, capturing the true geometry of the traditional interlaced pentagram. Through-holes at the five intersecting tips provide exact alignment for a matching drop-in star, while doubling as push-out points if the star needs to be removed after test-fitting. Specifications Dimensions: 180 mm x 120 mm x 3 mm Recess Depth: 1.0 mm (maintains a 2 mm solid floor) Alignment: Five 2.4 mm diameter positioning through-holes Print Settings: Prints flat on its back; no supports required
HELLO Name Sign, 112 x 36 mm
Desk or shelf name sign with raised bold HELLO lettering on a flat rounded-corner base plate. Letters are set in a heavy sans-serif so strokes stay thick enough to print cleanly. Plate: 112 x 36 x 3 mm, rounded corners Letters: 4 mm raised, Archivo Black, 22 mm cap size Print flat, no supports needed Two colour regions: plate and lettering, suited to a filament change at 3 mm Material: PLA or PETG
Nelore BCS Display Base
What it's for A structured, segmented display base designed to present five cattle models demonstrating Body Condition Scores (BCS). Features an elegant multi-tiered design with distinct angled platforms, giving each figure a dedicated presentation space without structural clutter. Dimensions Overall footprint: 400 mm length x 100 mm width. Total height: 20 mm (10 mm main base, 5 mm middle tier, 5 mm individual platforms). Display pads: 65 mm x 40 mm, offset at a 25-degree angle. Split halves: 200 mm length each, designed to fit cleanly on standard 256x256 mm print beds. Print notes Orientation: Print both base halves flat on their bottoms. Print the pegs horizontally as oriented in the file for maximum shear strength across the layer lines. Clearances: The dowel holes are 8.4 mm with 8.0 mm pegs. This 0.2 mm radial clearance is generous enough for easy assembly straight off a standard FDM printer, but tight enough to hold firmly with CA glue. Supports: None required. All chamfers and geometries are optimized for direct bed printing.