ATEN KVM Under-Desk Mount
Created today
Description
Under-desk sliding bracket pair tailored for the ATEN CS1944DP and similar 44mm-height desktop devices. Built with outward-facing mounting flanges for easy screwdriver access and a rear stop to prevent the unit from pushing back when plugging in cables.
- Clearance: 45.5mm internal height leaves 1.5mm of vertical wiggle room, accommodating a strip of standard foam tape to add friction and protect the chassis.
- Hardware: Countersunk holes oriented upwards, suited for #8 or M4 flathead wood screws.
- Versatile: Two-piece design means width isn't constrained. Space them out to match the switch exactly.
- Printing: Best sliced by rotating 90 degrees onto the outer side walls to print completely support-free.
Photos
Technical views
More like this
Explore more in Desk & Tech →
19.5mm Desk Edge Puck Mount
Edge-mounted charging cradle sized for the 33.5mm Google Pixel Watch magnetic puck. Designed to drop over a standard 3/4-inch (19.5mm) wood plank. Fitment: The 33.5mm bore sits at the rear of the housing. You push the puck in from the back, then slide the whole assembly over your desk edge — the wood itself traps the puck so it cannot back out. Cable Routing: An 8mm slot on the bottom allows the cable to drop cleanly out of the way. Incompatibilities: Does not fit full-sized phone Qi chargers or desks thicker than 19.5mm without adjustment. Phone hooks have been removed from this version.
355ml Can Tray & Angled Desk Stand
Two-piece modular desk platform with a precision-fit dovetail seam. The main tray spans 250x160mm and runs four custom 68mm bores—sized specifically to drop in 355ml soda cans with exactly 1mm of clearance so they never bind. The extension plate mates flush to the right edge via four full-depth dogbone locks. It carries over the four cable passthrough notches and builds into an 89mm-tall backing plate offset precisely to set up a 15-degree resting angle off the main tray's front partition. Built with squared alignment edges against the seam and a solid side-stop block to lock your gear into place. Critical Dimensions Host Standard: 355ml standard soda can (66mm body). Overall Footprint: 500mm wide by 160mm deep (assembled). Seam Clearance: Locks are cut with 0.25mm of total gap so they seat tight without filing.
Monolith Desk Marker
A heavy, brutalist-inspired desktop marker designed to hold its ground. This double-sided sign is carved deep with a high-impact sans-serif typeface, offering clear identification from either side of a workstation or counter. Design Notes Typeface: Archivo Black (heavy sans, regular weight). Base: Stepped 35mm footprint to prevent tipping on active desks. Carve Depth: 2mm inset text to catch overhead lighting and cast crisp internal shadows without requiring a multi-color print.
Handheld-Gehäuse mit herausnehmbarer Anschlussblende
Handheld-Gehäuse für eine selbstgebaute Konsole, bei dem die Kabel- und USB-Öffnung hinten nicht dauerhaft offen bleibt: Eine Klipp-Platte schließt sie und lässt sich bei Bedarf herausnehmen. Aussparung in der Rückwand: 100 × 30 mm, mittig Klipp-Platte: Außenrand 104 × 34 mm, Einsatz 99,6 × 29,6 mm, zwei Federarme mit Rastnasen, Fingermulde Innentiefe: 48 mm, Wandstärke 3 mm Display-Fenster 155 × 87 mm, Tastenlöcher 7,2 mm Druck: Schalen offen nach oben, Platte flach, ohne Stützen möglich
Pi 3 case
A bare Raspberry Pi 3 is so light that hooking up a standard HDMI cable instantly tips it off the desk. This case locks the board into a heavy enclosure and uses snap-on outer corner bumpers to give it some actual grip, so the board stays exactly where you put it. The port cutouts are oversized enough to accept real molded cables without them binding against the shell. Bed Fit: Everything is packed tightly to fit in a single run on a 180×180 mm print bed. Printing: All pieces sit flat on the plate. No supports required anywhere. Clearances: Built with a 0.4 mm gap around the board and lid joint so it slots together cleanly.
Aero — Windowed iPhone 13 Case
A custom-fit TPU or rigid shell for the iPhone 13. This model secures the device by preserving the upper retaining lip around the entire perimeter. The button zones have been converted from open edges into generous side windows—exposing the hardware for clean, tactile presses while maintaining the structural rigidity required for a snap-on fit. Features Retained Lip: The front edge wraps uninterrupted around the face of the phone to keep it locked in. Button Windows: Wide, centered side cutouts give your thumbs unobstructed access to the volume, mute, and power hardware. Camera & Port Clearance: Precise cutouts for the rear camera bump and the bottom lightning/speaker array. Print notes If printing in rigid filament (PLA/PETG), ensure your printer is well-calibrated; a slightly tighter tolerance may snap. TPU is recommended for the best balance of flex and grip.