Bote de basura innovador
Created today
Remixed once
Description
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias.
Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo.
Datos clave
- Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm
- Tres sectores de 120° separados por divisiones de 3 mm
- Aberturas de 76 mm de diámetro, una por compartimento
- Ruedas de 36 mm en cuatro soportes
- Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo
- La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Images
More like this
Explore more in Home & Fixtures →
Figure8 — Clip-On Cord Winder
Figure8 is a compact cord winder that snaps onto the flex of a kettle, toaster or similar appliance and takes up the slack. Wrap the spare cord around the two end horns in a figure-eight pattern, and the curled horn tips hold the turns in place so the wrapped cord can't spring loose. It is designed for cluttered counters where appliance cords tend to tangle. The spine carries a round channel with a narrower snap-in slot, so the winder stays on the cord instead of sliding off. The cord is pressed through the slot, and the lips flex to let it pass. Dimensions Overall length: 80 mm Overall width: about 46 mm across the horns Height: 9 mm Cord channel: 5 mm diameter, running the full spine Snap-in slot: 4 mm opening Features Four horns with tips curled back toward the centre Chamfered spine edges Single-piece body with no assembly Compatibility Intended for standard 6–7 mm appliance cords, which squeeze through the slot and sit snugly in the channel Print notes PETG or TPU is recommended, since the slot lips need to flex Stiff PLA may crack at the lips when the cord is pushed in Prints flat on the bed; the curled tips are short, so supports are only needed if the slicer flags them
Cricket Calcium Duster Tube With Inner Screen
A cricket calcium duster tube that keeps powder in one end and crickets in the other. Crickets get dusted when the tube is shaken, because the powder passes up through a screen. The fix is a threaded screen collar between the tube and the powder cap, so nothing prints inside the tube. Key numbers (75% scale) Tube: about 56 mm outside diameter, about 115 mm long, walls about 1.9 mm Threads: about 3.75 mm pitch, same thread on all pieces, so the caps are interchangeable Screen collar: 19 round holes, about 4.5 mm each, in a separate print Powder cap: deep cup for powder, threaded only at the rim Stop flanges: on the tube, so caps seat at a fixed depth Printing Prints open end up, no supports needed PETG recommended, 0.28 mm layers, 10 to 15% infill Four separate parts: tube, powder cap, cricket cap, screen collar
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
Tank Tap Bulkhead Fitting 1 1/2" BSP
A through-wall bulkhead fitting in the spirit of a classic water butt tank connector: a broad round flange sits against the tank wall, a long threaded barrel passes through, and a matching lock nut clamps it from the other side. 72 mm flange with a shallow gasket seat for a flat washer or O-ring 1 1/2" BSP-style male thread (47.8 mm major diameter, 11 TPI), 40 mm long 38 mm through bore Separate lock nut, printed alongside Design notes: The thread is a generic approximation of the Whitworth form, so test-fit against your mating part. Cut the tank hole to suit the thread, and use a rubber gasket against the flange. Print the flange face-down; PETG is a sensible choice for water contact.
Halterung mit Gegenstück für Hue-Lampe
Zweiteiliges Set: eine 170 × 45 mm Halterung mit zwei Befestigungslöchern und zwei Steckblöcken sowie ein Gegenstück mit Steckfassungen und einem Klipp-Tunnel für eine quer liegende Hue-Lampe (44 × 36 mm). Beide Teile sind auf Stabilität ausgelegt: dickere Grundplatte, breiter konischer Blockfuß, kräftige Fassungswände und eine dicke Wand über dem Tunnel. Halterung: Platte 8 mm, Blöcke 20 × 20 mm mit konischem Fuß (40 mm unten) Gegenstück: Fassungen mit etwa 6,7 mm Wandstärke, Sockel 70 mm breit Tunnel 44,8 × 36,6 mm, unten offen zum Einklipsen Querbohrungen 5 mm bzw. 5,4 mm Empfehlung: PETG, mindestens 3 Wandlinien, 40 % Infill