Brymen BM789 Multimeter Desk Stand
Created 1 months ago
Description
A dedicated desk stand for the Brymen BM789 multimeter.
The stand pitches the meter back at 30 degrees from vertical for bench readability. Crucially, the BM789 routes its test leads from the bottom face—so the lower lip and base plate feature a 65mm-wide central clearance channel. The meter sits on the outer shelves of the tray while the leads drop straight through to the desk.
Fitment checks
- Width: Internal clearance is 95mm (BM789 in holster is ~89mm wide).
- Depth: Internal tray depth is 55mm (BM789 in holster is ~51mm).
- Jacks: The 65mm U-channel easily clears the standard 4-jack spread.
- Compatibility: Will fit other meters with bottom jacks provided their holstered footprint is under 95x55mm.
Images
More like this
Explore more in Workshop & Tools →
Biofloc Monitor Station Enclosure
An enclosure is only as good as the snarl of wires it prevents. This is a heavy-duty two-part monitor housing built specifically for FDM printing, designed to group, separate, and anchor a complete suite of biofloc water-quality electronics without turning into a bird's nest inside. The layout isolates the battery compartment at the bottom and keeps the DC buck converters and relay in a ventilated top section, leaving the central deck clear for the ESP32 and an array of sensor interfaces. Internal divider walls double as cable routing channels, forcing the wiring to stay orderly. Core Features Printability: Both halves print completely flat on the build plate (Z=0). The integrated bottom handle is flush with the front face to avoid overhangs. Dimensions: 170 mm width × 250 mm height × 75 mm depth. Hardware Required: 6× M3 screws for the rear cover; additional M3 hardware for the internal standoffs and the 16x2 LCD faceplate mount. Ports: Bottom panel holds 4× sensor ports (3× 8mm, 1× 6mm) with engraved labels. Right panel holds cutouts for 12V DC, an SD card slot, a rocker switch, and USB programming access.
60mm Winding Spool With Anchors
What it's for A compact, highly functional utility spool tailored for winding wires or thin cables. It features two specialized holes: a 2.5 mm pass-through hole at the base of the core to thread the start of the wire, and a smaller 1.5 mm hole on the outer edge of the flange to secure the loose end once wound. Dimensions Outer Diameter (Flanges): 60 mm Core Outer Diameter: 25 mm Central Axle Hole: 8 mm Groove Width (Winding Space): 15 mm Flange Thickness: 2.5 mm each (Total height: 20 mm) Assembly Slide onto an 8 mm rod or bolt to spin. Pass the start of the wire through the inner bottom hole to anchor it, wind evenly across the 15 mm groove, and lock the tail through the outer top hole.
160mm Electronics Enclosure Unit
A two-piece industrial enclosure built for the SafeSuit Pro Worker Unit. Designed to house an ESP32, LoRa transceiver, and battery, with integrated cable management and hardware mounting points. The assembly uses a blind-screw design, pulling the cover tight against the base from the rear to leave the front face seamless. The cover includes an internal alignment lip for a rigid friction fit. Hardware Interfaces Internal Mounts: 4x posts for ESP32, 4x posts for LoRa module. Fasteners: Uses 4x M3 screws (inserted from the rear base). Control Cutouts: Recessed SOS button port (14mm bore), status LED port (4mm), lateral power switch slot, and right-side charging port. Cable Routing: Base features internal guide walls; cover features twin 7mm bottom-edge outlets for external sensor cabling.
Supervisor Electronics Shell
Generic hobby boxes crack at the screw posts the second time you open them, and their exposed hardware snags on everything in a bag. This is a clean, rugged shell that closes tight without external fasteners and keeps the wiring where it belongs. The front panel traps the alert button from the inside, so it can't be ripped out or jammed sideways. Internal Specs Dimensions: 120 × 75 × 35 mm external. Walls: 3 mm solid shell. Standoffs: Four integrated posts (2.5 mm bore) spaced for a standard ESP32 footprint. Clearance: 0.25 mm tolerance on the friction-fit lid lip. Print flat, no supports required.
Measure Stand
An arced 220mm-tall mounting stand for a measurer. Built with a solid base that secures to a desk and a precisely measured top block engineered for bolt-through attachment.
Industrial Wearable Electronics Enclosure
A heavy-duty three-part electronics enclosure designed for wearable prototype suits. Features a slide-and-lock fabric mounting plate that allows the main box to be removed without unthreading straps. Main Box: 140 × 90 × 40 mm with 3 mm walls and 10 mm side ports for external sensors. Mounting Plate: Slotted for fabric straps, featuring a male dovetail rail that slides into the main box and locks with a single pilot screw. Lid: Secures with four M3 screws into tapped corner bosses, featuring a 90 × 50 mm blank recess for a separate logo plate.