BSP 3/4 to 3/4 Hose Barb
Created 1 months ago
Description
An adapter coupling designed to step straight from a 3/4" BSP threaded fixture to a heavy hose. The hex nut transition is chamfered for support-free printing when oriented barb-down on the build plate.
Dimensions & Fit
- Thread: 3/4" BSP (26.4mm OD, 14 TPI)
- Barb: 21.2mm maximum outer diameter (5-stage reversed taper)
- Bore: Steps from 20mm at the threaded end down to 14mm at the barb to maximize flow rate.
- Wrench Flats: ~31mm flat-to-flat
- Printing: Print barb-side down; no supports required.
Images
More like this
Explore more in Home & Fixtures →
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Cardboard Sign Corner Holder for Wall
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad. Slot height: 3.4 mm for 3 mm cardboard Leg length: 40 mm per corner Back plate: 2 mm, flat side faces the wall Front lip: 1.6 mm, with a cut-out window Print: flat on the back, no supports, one per corner (4 for a sign)
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
Advent Calendar Drawer With Grip
A single replacement drawer for an Advent calendar: open-top box, 41.5 × 23.5 × 44 mm, 1.5 mm walls and floor, with the number engraved on the front above a small square grip. Remix hooks Grip size: 8 × 5 mm face, 4 mm projection (5 mm deep body, 1 mm embedded). Make it wider for easier pulling. Grip rounding: 0.8 mm edge rounding. Raise it for a softer look, drop it for a sharper square. Number: 8 mm Roboto, engraved 1 mm deep near the top. Change the digit for other drawers. Fit: trim 0.2 mm off width and height if it binds in the frame. Pairs with: the other numbered drawers, since the front footprint is unchanged.
Wavy Bobby-Pin Sock Clip
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece. Remix hooks Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin. Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more. Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks. Hook radius: 15 mm. Enlarge it for thicker rack rails. Pairs well with a mesh laundry bag. The clip section is 70 mm long and about 15 mm wide. The hook sits above that.
G 1 1/4" Plug with Concave End
What it's for A male-threaded plug for a G 1 1/4" (BSP parallel) port, such as a bull nose fitting. The end face is dished (concave) so it seats against a rounded nose. Dimensions Thread: G 1 1/4", 41.91 mm major diameter, 2.309 mm pitch (11 TPI) Thread length: 20 mm Hex head: 50 mm across flats, 10 mm tall Concave dish: 30 mm sphere radius, 5 mm deep Remix ideas Change the dish radius or depth to match a different nose profile. Add a gasket groove under the hex head. Swap the hex for a knurled round head for hand tightening.