Caixa 120x120x50 mm Estação Meteorológica
Created today
Description
Caixa quadrada de 120 × 120 × 50 mm com paredes de 2 mm e tampa separada, fixada por quatro parafusos M3 nos cantos. Possui abertura para display, chave gangorra, entrada USB-C e fendas de ventilação, além de duas fendas para alça na parte superior da lateral.
- Parafusos: 4 colunas de canto, furo de 2,8 mm na base e 3,4 mm com escareado na tampa
- Display: abertura de 24,4 × 14,4 mm na tampa
- Chave gangorra: abertura de 15,3 × 10,3 mm na tampa
- USB-C: abertura de 9 × 4 mm na lateral +X
- Alça: duas fendas de 16 × 4 mm no alto da parede +Y, a 30 mm do centro para cada lado
- Ventilação: fendas nas laterais, longe das colunas, com fendas extras na região dos sensores
- Protoboard: dois trilhos baixos no fundo como guia provisório
- Impressão: base e tampa separadas, sem suportes necessários
Images
More like this
Explore more in Storage & Organization →
Drawer Sleeve Box With Mounting Pad
Open-top rectangular sleeve, 86 x 52 x 127 mm, for a sliding drawer. Smooth interior, 1.6 mm floor, sides and front, 2.4 mm back wall. A raised 40 x 40 x 3 mm pad on the back carries two M3 nut traps. Remix hooks Pad position: top edge sits 10 mm below the rim; pad is centered in X. Move or resize freely. Nut traps: 5.7 mm hex, 2.5 mm deep, 25 mm apart, with 3.4 mm blind holes behind them. Blind holes stop 0.8 mm short of the inside; thicken the back wall to go deeper. Edges: 3 mm vertical rounding, 6 mm 45° bottom chamfer (prints without supports). Drains: two 3 mm holes at X = ±20 mm. Pairs with a matching drawer 3 to 4 mm smaller in each direction.
Dual Crossover Enclosure
A scalable enclosure updated to house two crossover PCBs vertically. Features integrated external mounting tabs for MDF, top-edge ventilation slots for passive cooling, and a reinforced front panel with standard 19mm-spaced 4.5mm holes for banana plug binding posts. Internal capacity: 200x170x60mm Cooling: 4mm vertical ventilation slots Mounting: 4x external tabs with countersunk 4mm screw holes
Vented Power Supply Enclosure
What it's for A custom-sized, two-part vented enclosure designed to hold a 111x79x36mm power supply. It features side-mounted cooling vents, a solid base, and wire-routing holes positioned near the bottom of the narrow end. Dimensions External size: 99 x 131 x 42 mm (main box), plus the flush-fitting lid. Internal space: The central cavity between the corner screw pillars provides a clear 83 x 115 mm footprint, allowing a 2 mm clearance gap on all sides for the 111 x 79 mm power supply unit. Wire routing: Two 7mm diameter holes on the narrow end for cable pass-through. Assembly The lid secures into the four corner pillars using standard M3 screws. The interior features a small alignment lip on the lid to ensure it seats squarely against the posts.
Endgame Robotics Enclosure
A rugged, multi-part enclosure designed for robotic interfaces and smart control nodes. The three-piece split allows easy assembly, with a deep main chassis to house microcontrollers and batteries, capped by a clean windowed bezel and a vented back cover. Front Bezel: Features a recessed touch panel land and tiny microphone breakout holes. Main Chassis: Houses dual text debossing ("END" / "GAME"), structural columns for heat-set inserts, and a USB-C cutout. Back Cover: Includes countersunk M3 mounting holes, an expansion module bay, and a hexagonal vent grille.
Vented Equipment Enclosure Box
What it's for A functional electronics or equipment enclosure featuring an integrated hinged lid, snap latch, and generous ventilation slots. Designed to print easily with the lid flat on the bed alongside the main body. Dimensions Internal capacity: 200 x 200 mm base, 60 mm deep inside Floor: 5 mm thick solid base for structural rigidity Cutouts: A 30 mm circular port on the left wall, and a 12x6 mm rectangular port on the back wall by the hinges. Cooling: Vertical slot vents on the front, left, and back panels. Assembly Once printed, mate the hinge knuckles of the lid to the base. Slide a piece of raw 1.75mm or 3mm filament (or a standard M3 bolt) straight through the hinge line to join them.
Caja sci-fi para ESP32, RCA y driver
Caja para electrónica con ESP32, dos salidas RCA, jack DC hembra y un driver que no entraba cómodo: los conectores de la pared derecha quedaban pegados al driver. Ahora la caja es más larga y hay luz entre ambos. Medida exterior: 132,8 × 60 × 28,8 mm. Separación: unos 26 mm entre los postes del driver y la pared con RCA y jack. Conectores: dos agujeros de 8,2 mm (RCA) y uno de 11,2 mm (jack DC), frente a la ranura USB. Montaje: 4 tornillos M3 en las esquinas; la tapa lleva rejillas y ranuras decorativas. Impresión: base y tapa por separado, sin soportes si se imprime la base apoyada en el fondo.