Car Visor Sunglasses Clip
Created 5 months ago
Description
A handy, snap-on clip for your car's sun visor that keeps your sunglasses securely within reach.
What it's for
Perfect for keeping your sunglasses or driving glasses safe and accessible while driving. It simply slides over the sun visor and grips the arms or bridge of your glasses, preventing them from sliding around or getting scratched in the center console.
Dimensions
The main upper clip is sprung to fit standard car sun visors ranging from 8mm to 12mm thick, opening up to 14mm. The lower glasses retainer features a tapered opening designed to firmly grip frames anywhere from 2mm to 6mm thick.
Remix ideas
- Widen the lower clip to accommodate exceptionally thick or chunky frames.
- Add a secondary side-slot to hold parking passes or toll tickets.
- Emboss your name, initials, or car model on the flat front face.
Photos
Technical views
More like this
Explore more in Automotive, RC & Hobby →
Ajman car tray
A rectangular coffee tray for the car, measuring 124.7 mm wide by 107.4 mm deep, with a raised rim and a recessed inner surface that keeps cups and items in place. "Meet me in Ajman" is engraved into the inner floor, centered. 124.7 × 107.4 mm footprint, 10 mm tall 4 mm raised walls with rounded corners Recessed floor, 6 mm below the rim Text engraved 1 mm deep, not raised Flat bottom, single solid piece, no supports needed
Curved Snap-In Interior Trim Cover
A 123 × 180 mm curved interior trim cover with a straight bottom edge, a stepped outline (107 mm wide at the top, 123 mm in the lower 85 mm) and a 3 mm panel. The perimeter flange follows the crowned surface so the part sits flush around the opening. Remix hooks Surface crown: the front curvature is a few millimetres in both directions. Flatten or deepen it to match a measured body profile. Raised area: 10 mm high with a soft ~30 mm blend at the upper left. Change height or width to suit. Clips: five per side at 18, 54, 90, 126 and 162 mm, 14 mm wide and 4.5 mm thick, with a ~2 mm hook. Adjust hook depth to the real metal edge thickness. Rear frame: 15 mm deep, 2.8 mm wall, inset 3.5 mm. Change the inset for a tighter or looser fit. Pairs with: fuzzy skin in the slicer for a textured look. Print in PETG, ASA or ABS.
Car Coffee Tray shj
A rectangular car coffee tray, 124.7 × 107.4 mm and 10 mm tall, with a raised 4 mm rim and a recessed floor to keep cups and items in place. "meet me in SHJ" is engraved 0.8 mm deep into the floor in the bottom-right corner. Remix hooks Text weight: the letters are 7 mm tall with strokes thickened by 0.3 mm per side. Raise that for a bolder engraving, or drop it to return to the plain font weight. Text size and position: 7 mm size, 5 mm in from the rim. Change the inset to move it, or switch the alignment to centre it. Rim and floor: 4 mm wall and 4 mm floor thickness. A taller rim holds more, a thinner floor saves filament. Pairs with: a non-slip mat under the base, or a cup-sized ring added to the floor.
Aura — Automotive Ring Emblem
Llavero personalizado con el nombre "NOAH" en letras mayúsculas e inclinadas, diseñado con la temática de su personaje favorito. Cuenta con la silueta clásica asomándose por el anillo dorado, perfecto para colgar en la mochila o en las llaves. Características Diseño dinámico: Letras gruesas e inclinadas para dar sensación de velocidad. Impresión a dos colores: El diseño está dividido en dos alturas distintas. Cambia el filamento a los 3 mm para que el texto y el relieve resalten sobre el fondo. Resistente: Base sólida de 3 mm de grosor que aguanta los tirones del uso diario.
67mm Lens Cap Strap Clip
Pinching off a lens cap and immediately dropping it in the dirt is an avoidable mistake. This clip mounts directly to a camera strap to hold a 67mm pinch cap securely while the lens is in use, keeping it out of your pockets and off the ground. Strap slot: 42mm wide with a 3.2mm clearance and a diagonal slip-channel, letting it twist onto the webbing without unthreading the strap. Cap receiver: 67.5mm internal groove catches the cap's pinch prongs, with an angled lip to lock them in place. Tether loop: 6mm bore on the side to run a backup paracord lanyard. Print orientation: Internal overhangs are angled to print support-free when placed face-up on the plate.
RC Car Bevel Gear Rear Drive
A rear-axle drive for an RC car where the motor shaft has to turn 90° into a cross-car axle without the gears skipping or the motor shifting. This set uses a 12-tooth pinion and 24-tooth crown gear (2:1) on a 103.9 mm × 6 mm axle, with an open motor cradle instead of a closed box. Key numbers Gears: module 1.5, 20° pressure angle, 4 mm face width, 90° shaft angle Pitch cone angles: 26.57° (pinion) and 63.43° (crown); cone distance about 20.1 mm Pinion bore 2.1 mm, crown bore 6.2 mm, both with M3 set-screw holes in the hubs Axle supports: 6.4 mm through-hole plus a 17.3 mm seat for 606 bearings (6×17×6) Base: 84 × 92 × 5 mm, M3 holes (3.4 mm clearance); cradle slots allow forward and back adjustment Motor cradle parameters at the top of the file: mw, mh, wall, saddlel, saddley. Measure the real motor and edit them Cover is open at the bottom, with two M3 ears at the rear Printing Print gears with the hub facing up or down on the bed; PETG or nylon preferred Cover prints open-side up without supports Axle is a separate 6 mm steel rod; M3 screws hold supports, cradle, straps and cover