Carbon Pill Membrane Dome
Created 1 months ago
Description
A replacement buckling membrane dome designed for custom keyboards and keypads, optimized for a carbon contact pill.
- Pill Cavity: A 2mm diameter, 0.4mm deep recess inside the top roof holds a standard carbon contact pill.
- Anti-Tilt Mass: The upper section is kept thick and rigid, forcing the thin side walls to buckle evenly and keeping the pill traveling straight, even on off-center strikes.
- Air Relief: Base channels prevent suction on the return stroke.
Photos
Technical views
More like this
Explore more in Desk & Tech →
Aero — Windowed iPhone 13 Case
A custom-fit TPU or rigid shell for the iPhone 13. This model secures the device by preserving the upper retaining lip around the entire perimeter. The button zones have been converted from open edges into generous side windows—exposing the hardware for clean, tactile presses while maintaining the structural rigidity required for a snap-on fit. Features Retained Lip: The front edge wraps uninterrupted around the face of the phone to keep it locked in. Button Windows: Wide, centered side cutouts give your thumbs unobstructed access to the volume, mute, and power hardware. Camera & Port Clearance: Precise cutouts for the rear camera bump and the bottom lightning/speaker array. Print notes If printing in rigid filament (PLA/PETG), ensure your printer is well-calibrated; a slightly tighter tolerance may snap. TPU is recommended for the best balance of flex and grip.
Solid Back iPhone 13 Case
A custom-fit TPU or rigid shell for the iPhone 13 that prevents the phone from slipping or taking raw impacts on the edges. The back is a solid panel for maximum protection. The button zones feature wide windows rather than thin button-covers, exposing the actual hardware so you get the real tactile click of the buttons without fighting the case material. Print Notes Fit Tolerance: Exact to the iPhone 13 body (71.5 mm x 146.7 mm). Material: TPU is highly recommended to let the lip flex over the screen edge. Rigid filaments like PETG will be a very tight snap-fit.
Handheld-Gehäuse mit herausnehmbarer Anschlussblende
Handheld-Gehäuse für eine selbstgebaute Konsole, bei dem die Kabel- und USB-Öffnung hinten nicht dauerhaft offen bleibt: Eine Klipp-Platte schließt sie und lässt sich bei Bedarf herausnehmen. Aussparung in der Rückwand: 100 × 30 mm, mittig Klipp-Platte: Außenrand 104 × 34 mm, Einsatz 99,6 × 29,6 mm, zwei Federarme mit Rastnasen, Fingermulde Innentiefe: 48 mm, Wandstärke 3 mm Display-Fenster 155 × 87 mm, Tastenlöcher 7,2 mm Druck: Schalen offen nach oben, Platte flach, ohne Stützen möglich
Pi 3 case
A bare Raspberry Pi 3 is so light that hooking up a standard HDMI cable instantly tips it off the desk. This case locks the board into a heavy enclosure and uses snap-on outer corner bumpers to give it some actual grip, so the board stays exactly where you put it. The port cutouts are oversized enough to accept real molded cables without them binding against the shell. Bed Fit: Everything is packed tightly to fit in a single run on a 180×180 mm print bed. Printing: All pieces sit flat on the plate. No supports required anywhere. Clearances: Built with a 0.4 mm gap around the board and lid joint so it slots together cleanly.
Micro Print-in-Place Joystick
This is a miniature print-in-place joystick that functions as a tactile desk toy. The internal geometry has been rebuilt to ensure the ball joint prints cleanly without supports or mid-air extrusion failures.
XIAO ESP32-S3 Chatbot Shell
Boîtier compact conçu pour intégrer une carte Seeed Studio XIAO ESP32-S3 Sense avec caméra, un écran TFT de 1,54" en façade et un haut-parleur plat (3525). L'ensemble se ferme via un tiroir coulissant en sous-face. Vérifications de montage : L'écran s'insère par l'intérieur (espace pour PCB de 32x43,7 mm). La carte XIAO repose sur une butée interne située à 43,7 mm du fond, avec une profondeur d'appui de 15 mm. La caméra pointe par le trou carré de 10 mm en façade. L'accès USB-C sort par le haut. Le haut-parleur 3525 s'encastre à fleur par l'extérieur du toit.