Cardboard Sign Corner Holder for Wall
Created today
Description
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad.
- Slot height: 3.4 mm for 3 mm cardboard
- Leg length: 40 mm per corner
- Back plate: 2 mm, flat side faces the wall
- Front lip: 1.6 mm, with a cut-out window
- Print: flat on the back, no supports, one per corner (4 for a sign)
Images
More like this
Explore more in Home & Fixtures →
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Wall Shelf, 20 cm Glue-On
A small wall shelf that sits flat against the wall and glues on, with no drilling and no screws that miss the stud. The tall back plate gives the adhesive a big flat face, and two triangular gussets stop the front edge from sagging or peeling off. Key numbers Shelf top: 200 mm long x 80 mm deep x 4 mm thick Back plate: 200 x 40 mm, 4 mm thick, flat on the wall side Two gussets, 4 mm thick, each 34 mm tall Print: shelf upright on its back plate or flat on the top, no supports needed with the plate down; PETG or PLA, 3+ perimeters Glue: construction adhesive or mounting tape on the back plate face
Lifebuoy — Wall Key Rack
Lifebuoy is a wall-mounted key rack shaped like a beach lifeguard buoy, with a red body, white LIFEGUARD lettering and five sturdy hooks. Features 230 mm long stadium-shaped body, 70 mm tall, 14 mm deep Letters as a separate white piece set into a pocket in the red body Five round-tipped hooks along the lower front Two rear keyhole-style screw holes with counterbores Flat back for printing without supports Print notes Print the body and the letters in separate colours (PLA, 0.4 mm nozzle), back face down.
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
Advent Calendar Drawer With Grip
A single replacement drawer for an Advent calendar: open-top box, 41.5 × 23.5 × 44 mm, 1.5 mm walls and floor, with the number engraved on the front above a small square grip. Remix hooks Grip size: 8 × 5 mm face, 4 mm projection (5 mm deep body, 1 mm embedded). Make it wider for easier pulling. Grip rounding: 0.8 mm edge rounding. Raise it for a softer look, drop it for a sharper square. Number: 8 mm Roboto, engraved 1 mm deep near the top. Change the digit for other drawers. Fit: trim 0.2 mm off width and height if it binds in the frame. Pairs with: the other numbered drawers, since the front footprint is unchanged.
Dragon Head Blind Cord Cleat
Blind cords slip off a plain cleat the moment the tension changes. This dragon head cord cleat has a tusk on each side of the snout, so the cord wraps under it and stays put. Mounting plate: 30 x 70 mm, 4 mm thick, two countersunk screw holes Tusks: ball-tipped, project about 16 mm out from the centre on each side, above the cord path Cord slot: 3.5 mm tall, runs left to right through the snout Flames: three tongues from each nostril, pointing forward over the plate Extras: horns, brow ridges, cheek spikes Print: plate flat on the bed; the horns and flames are small overhangs, so a little cleanup or supports may help