Caregiver Check Station Enclosure, Gray and Red
Created today
Description
A caregiver check-in box with no obvious place to tap, and a back panel that fights you at every repair. This enclosure puts a large red TAP HERE panel on the front and a screw-on back cover behind it, so the electronics come out without disturbing the front.
- Size: 150 × 110 × 36 mm body, with a 3 mm back cover.
- NFC panel: 64 × 64 × 2 mm red panel, replaceable, behind a 1.5 mm lip. It is held by a separate holder with four M2.5 screws.
- Back cover: four M3 × 12 screws into body posts, with a 0.3 mm clearance skirt. Two keyhole slots handle wall mounting.
- Openings: PIR window 23 mm, three 5 mm LED holes (green, yellow, red), BME280 air slots, 12 × 6.5 mm USB-C slot, 5 mm reed-switch cable hole, and top and bottom vent slots.
- Printing: body and panel face-down, cover outside-down. PLA, no supports, 3 walls, about 15% infill.
- Not final: every board position is a placeholder. Measure the ESP32, PN532, PIR and BME280 before fixing the internal layout.
Images
More like this
Explore more in Storage & Organization →
Screw-Through Dowel Shelf Bracket
A two-part wall bracket for holding a 13 mm wooden dowel, intended as a filament spool shelf. A narrow wall plate carries a ledge that takes the vertical load, and a separate flat-printed arm rests on that ledge. One screw passes through the arm's back flange and the wall plate into the wall, locking the two parts together. The screw head sits in a recess in the arm. Wall plate: 24 mm wide, 84 mm tall, with a ribbed ledge under the arm Arm: 12 mm thick, printed on its side with no supports Dowel hole: 13.6 mm, 150 mm out from the wall plate Fixing: one screw near the top, shared by both parts Print two sets for a pair of brackets
Tabletop Wildlife Alert, 100 mm Diamond Sign
Modular tabletop wildlife-warning prototype printed as separate parts that bolt together: base, three pole sections, four brackets, electronics enclosure with lid, PIR sensor housing with rain hood and lid, amber light housing with lid, and a diamond sign reading WILDLIFE CROSSING with no graphic. The stack runs bottom to top: electronics enclosure, PIR sensor facing forward, two amber LED openings, then the sign. Each housing screws to its own bracket, and each bracket clamps onto the pole with one cross-screw. Dimensions (mm, outside) Electronics enclosure: 70 × 60 × 50, interior about 65 × 57 × 45, with lid PIR housing: 60 × 40 × 35, 23 mm lens opening, rain hood, with lid Light housing: 70 × 35 × 30, two 8 mm LED openings, with lid Sign: diamond 100 point to point, 3 mm thick Base: 100 × 84 × 6 Pole: three sections, 20 × 20 × 58 Overall height: about 224 To confirm before printing Controller board size (a full Uno will not fit the interior) PIR lens diameter and LED diameter (23 mm and 8 mm are placeholders) Printer build area Electronics are untested
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Caixa 120x120x50 mm Estação Meteorológica
Caixa quadrada de 120 × 120 × 50 mm com paredes de 2 mm e tampa separada, fixada por quatro parafusos M3 nos cantos. Possui abertura para display, chave gangorra, entrada USB-C e fendas de ventilação, além de duas fendas para alça na parte superior da lateral. Parafusos: 4 colunas de canto, furo de 2,8 mm na base e 3,4 mm com escareado na tampa Display: abertura de 24,4 × 14,4 mm na tampa Chave gangorra: abertura de 15,3 × 10,3 mm na tampa USB-C: abertura de 9 × 4 mm na lateral +X Alça: duas fendas de 16 × 4 mm no alto da parede +Y, a 30 mm do centro para cada lado Ventilação: fendas nas laterais, longe das colunas, com fendas extras na região dos sensores Protoboard: dois trilhos baixos no fundo como guia provisório Impressão: base e tampa separadas, sem suportes necessários
Inverted Glue Bottle Stand
Keep viscous liquids like glue or ketchup primed and ready at the nozzle. Storing bottles inverted ensures immediate dispensing, eliminating the wait for a half-empty bottle to drain toward the cap. The stand is designed with a stable tripod base and precise clearances to hold the bottle securely while catching any rogue drips. Design specifications: Sized to cradle a 45mm bottle body Integrated 30mm drip cup positioned directly under the nozzle Beveled entry ring guides the bottle smoothly into place Tapered support arms print cleanly without support material Wide footprint prevents tipping even with a full, top-heavy bottle
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.