CR-80 Vertical ID Blank
Created 1 months ago
Description
Vertical ID badge blank cut to exact CR-80 standard specifications.
Built to mate with standard lanyard straps and bulldog clips. The rigid 1.6mm plate thickness ensures it stays flat during use, but means it will not fit into thin single-card vinyl sleeves intended for standard 30-mil PVC cards.
Fitment Dimensions
- Overall Card Size: 53.98mm W × 85.6mm H
- Thickness: 1.6mm
- Corner Radius: 3.18mm (1/8")
- Clip Slot: 14.5mm × 3.5mm (standard slot punch)
Images
More like this
Explore more in Desk & Tech →
Vertical Arc Reactor Speaker Stand
What it's for A vertical, upright stand designed to hold an Echo Dot 3rd Gen while transforming it into a glowing reactor core. The custom cavity is deep enough to cover the sides of the device entirely, leaving only the top surface and the signature light ring visible from the front. A bottom channel allows the power cable to route straight down seamlessly. Dimensions Base: 120 × 100 mm footprint for vertical stability. Speaker Cavity: 101.5 mm diameter, 44 mm depth (tailor-made to enclose the puck). Overall Height: ~150 mm. Print notes Orientation: Prints best as oriented. Ensure your bridging settings are dialed in for the speaker cavity and the rear acoustics hole. Supports: You may want light supports under the bottom edge of the ring and inside the cable channel, depending on your printer's overhang capabilities. Assembly: Slide the Echo Dot in from the front, route the barrel plug up through the bottom slot, and plug it in.
Reactor Core Echo Stand
This stand pitches your 3rd Gen Echo Dot on its side to make it the glowing core of a Mark I Arc Reactor. The base features a U-shaped drop-in pocket sized perfectly for the Dot — it slides right in from the top with the cable attached, seating securely behind the front bezel. The front face frames the bottom edge of the device, turning its status light into the reactor's ring. Core Features Drop-in Dock: Fully open top channel and rear cable slot let you drop the Dot in without unplugging it. Reactor Bezel: Oversized front ring complete with ten staggered copper-style cooling coils. Embossed Text: The iconic 'PROOF THAT TONY STARK HAS A HEART' circles the top arc of the bezel. Cable Management: Rear cutout safely clears the bulky power adapter plug, and the hollowed base lets you run cables beneath.
Lazy-Tongs Piano Bottle Caddy
A pantograph-style drink arm in the spirit of a vintage lazy-tongs: a hooked clip straddles the top of a piano's music desk, and a three-unit scissor mechanism unfolds backward to carry a bottle cup. The cup sits inside a wide, rimmed drip tray, so condensation stays off the keys and cabinet. The arm folds flat for storage and stretches out for use. Pivots are print-in-place pins, and the two end joints ride in slots so the arms can open and close. Design notes Cup bore is 76 mm, sized for a standard 33.8 fl oz (1 L) water bottle; cup wall is 85 mm tall. Drip tray is 96 mm across with a 12 mm rim and sits flush with the arm plane. Clip slot fits a music desk about 13 mm thick; adjust the thickness value to suit your piano. Three colored regions: desk clip, scissor arms, cup and tray. Shown in a partly extended pose; the opening angle can be changed to show it folded or fully reached. Best printed as shown, with 0.4 mm clearances at the pivots. Support is only needed under the clip hook. A full bottle is a cantilever load, so keep the arm short for heavier bottles.
Handheld-Gehäuse mit herausnehmbarer Anschlussblende
Handheld-Gehäuse für eine selbstgebaute Konsole, bei dem die Kabel- und USB-Öffnung hinten nicht dauerhaft offen bleibt: Eine Klipp-Platte schließt sie und lässt sich bei Bedarf herausnehmen. Aussparung in der Rückwand: 100 × 30 mm, mittig Klipp-Platte: Außenrand 104 × 34 mm, Einsatz 99,6 × 29,6 mm, zwei Federarme mit Rastnasen, Fingermulde Innentiefe: 48 mm, Wandstärke 3 mm Display-Fenster 155 × 87 mm, Tastenlöcher 7,2 mm Druck: Schalen offen nach oben, Platte flach, ohne Stützen möglich
Pi 3 case
A bare Raspberry Pi 3 is so light that hooking up a standard HDMI cable instantly tips it off the desk. This case locks the board into a heavy enclosure and uses snap-on outer corner bumpers to give it some actual grip, so the board stays exactly where you put it. The port cutouts are oversized enough to accept real molded cables without them binding against the shell. Bed Fit: Everything is packed tightly to fit in a single run on a 180×180 mm print bed. Printing: All pieces sit flat on the plate. No supports required anywhere. Clearances: Built with a 0.4 mm gap around the board and lid joint so it slots together cleanly.
