Detailer's Triptych Vacuum Set
Created 1 months ago
Description
A custom trio of detailing tools designed specifically for the standard 35mm friction-fit wands found on most Karcher wet/dry workshop vacuums. Each piece serves a distinct stage of an automotive deep clean.
The set features:
- The Crevice Tool (Red): Extended and sharply angled to slip between seats and center consoles.
- The Wide Nozzle (Blue): Flared to 80mm with a shallow scraping edge, ideal for lifting stubborn dirt from floor mats and broad upholstery.
- The Detailing Spot Nozzle (Green): Narrowly focused into a 16mm tip for intense, localized suction inside cup holders, vents, and door pockets.
Designed to print without supports—just drop them on the bed vertically.
Photos
Technical views
More like this
Explore more in Workshop & Tools →
Zauberstab Verschluss 3.1
Zweiteiliger, hohler zylindrischer Testkörper zur Prüfung von FDM-Toleranzen. Beide Teile verfügen über eine geschlossene Außenwand und schließen bündig ab. Feste Abmessungen: Außen 30.8 mm, Innen 21.8 mm Mindestwandstärke: 1.5 mm im kritischen Bereich der Nuten Mechanismus: Bajonettverschluss mit Arretierungsnocke gegen unbeabsichtigtes Öffnen Druckbar: Ohne Stützstrukturen, flach auf dem Druckbett positioniert
Wide Stance Filament Spool Stand
Filament spools that hang off the edge of undersized holders are a constant source of drag and jams. This A-frame stand widens the track, catching oversized spools before they can derail. Fit and Bed Limits Inner Clearance: 160 mm between the uprights Base Width: 180 mm Spindle Height: 192 mm Printability: The entire layout is spaced to fit on a 220x220 mm bed without needing rotation or supports.
20 mm Round Disc, 2 mm Thick
A flat 20 mm round disc, for when a 2D circle needs to become something you can print and hold. A bare circle has no thickness, so this gives it enough to print as a solid piece. Print details Diameter: 20 mm Thickness: 2 mm (assumed, since a plain circle has no height) Sits flat on the bed, no supports needed Prints in any filament
Embroidery Hoop Clearance Frame
A single-piece clearance frame for testing fabric fitment against the dimensions of the Brother SA431 / EF61 small embroidery hoop. Designed for FDM printing as a rigid, continuous ring, it skips mounting hardware in favour of a plain profile for preliminary dimensional checks. Inner clearance: 50 mm × 38 mm Overall footprint: 60 mm × 48 mm Frame width: 5 mm uniform wall Thickness: 4 mm Z-height
DopplerSled — Physics Pendulum Carrier
DopplerSled er en specialdesignet slæde til fysikforsøg med dopplereffekten. Telefonen hviler på den flade ryg og mod bundstoppet, mens elastikker i sidehakkene holder den fastspændt. Konstruktionen giver maksimal plads til telefonens egne højttalere, og topørets to huller sikrer et stabilt pendulsving uden rotation. Design Universelt fit: Ren L-profil uden frontlæbe betyder at alle telefonstykkelser og covers passer. Printbarhed: Designet lægger sig helt fladt på byggepladen og kan printes helt uden supports. Akustik: Stor centerudskæring lader lyden bære bagud. Montering Placer telefonen, sæt to elastikker over skærmen ved sidehakkene, og træk to snore gennem tophullerne til stativet.
IV Central Line Wrench
Luer lock connections jam at the worst possible moments, and trying to twist a wet, over-tightened collar with gloved fingers is a lost cause. This is a pocket-sized dual-ended wrench designed to grip those lines without crushing them. It slides right over the tubing and engages the radial ridges on the collar so you can break it loose in one turn. Fit & Printing Large End: 10.2mm inner bore with 1.5mm bite notches (clears 6mm tubing). Fits standard IV collars. Small End: 8.0mm inner bore (clears 5mm tubing). Fits tighter hubs. Thickness: 5mm solid body with ergonomic thumb dimples. Print Settings: Print flat on the bed. Needs 3-4 perimeters for structural rigidity so the open ends don't flex under torque. No supports required.