Description
Rectangular block, 100 mm long, 24 mm wide and 15 mm tall, with a 16 mm wide by 11 mm deep groove running the full length along the top centre. The groove size is engraved into the groove floor as "16 x 11 mm".
- Overall size: 100 x 24 x 15 mm
- Groove: 16 mm wide x 11 mm deep, open at both ends
- Side walls: 4 mm; floor: 4 mm
- Engraving: 0.6 mm deep, readable from above
- Prints flat with no supports
Photos
Technical views
More like this
Explore more in Workshop & Tools →
outside hat
A plain flat disc in the spirit of an oversized washer or a vinyl-record blank: 3 inches across, 1/8 inch thick, with a clean 1 cm hole through the centre. Prints flat with no supports. Diameter: 76.2 mm (3 in) Thickness: 3.175 mm (1/8 in) Centre hole: 10 mm Good for spacers, coasters, templates, or as a base for other builds
Klipper Display and Status Console
Compact left-side mounting enclosure for Klipper printer telemetry, designed specifically for the Ender 3 Pro 2040 vertical extrusion. Hardware Compatibility: Fits a 1602A I2C LCD, a 32x32mm HW-109 MAX7219 LED Matrix, and a standard 5mm RGB LED. Internal Clearance: 36mm cavity depth cleanly clears standard I2C backpacks. Mounting System: Left-oriented 5mm side flange using dual slots for M4 t-nuts. Flange sits flush to the bottom, leaving top clearance for gantry travel. Assembly: Snap-fit 2mm front panel with internal screw bosses; back plate secured via four M3 interior corners. The housing prioritises rigidity and short wiring paths over bulk, anchoring firmly without compromising structural frame limits.
Zauberstab 3.3
What it's for Zweiteiliger Zauberstab mit Griff für eine UV-Lampe und aufdrehbarer Spitze. Drei dicke, runde Stränge winden sich wie aufgeklebte Teigschlangen um den Stab und laufen in der verriegelten Endstellung von Griff zu Spitze durch. Dimensions Griff: 87 mm hoch, 85 mm Innenhöhe, Innendurchmesser 21,8 mm Spitze: 135 mm inklusive Zapfen, verjüngt sich nach oben Rillengrund Ø 26,4 mm, Strangkuppen ca. Ø 30,4 mm Lichtkanal in der Spitze von 18 mm auf 9 mm Vier Bodenlöcher Ø 3,75 mm Remix ideas Strangzahl oder Drehung ändern Strangdicke anpassen Andere Muster wie Borke oder Astlöcher
Custom Hex Standoff Tube
Off-the-shelf hardware never matches the exact gap, leaving assemblies rattling or crushed. This custom hex standoff fills the exact space needed while keeping the internal bore clear for a rod or bolt to pass through. Dimensions Height: 55.0 mm (5.5 cm) Outer Profile: 5.15 mm point-to-point hexagon Inner Bore: 2.50 mm diameter
Baluster Drill Jig
A precise drill guide for 1.375-inch square balusters. Centers a 3/8-inch bore perfectly in the end grain. Features an open-corner skirt that drops down two inches to grip the baluster on all four sides, ensuring plumb alignment while letting you easily verify the jig is seated fully against the wood. The center windows in the tabs save print time and reduce material waste. Printing Fitment The internal bore is modeled with clearance for a 3/8-inch bit so it spins freely without melting the plastic, and the skirt has 0.5mm total clearance to slip cleanly over milled lumber. Measure your balusters before printing — milled dimensions can vary depending on moisture and the lumber yard.
Precision Rectangular Spacer Frame
Ein präziser, flacher Rechteckrahmen mit zentriertem Ausschnitt. Das Profil eignet sich gut als Abstandshalter, Passepartout oder Montage-Shim. Außenmaße: 39 × 30 mm Dicke: 3 mm Ausschnitt: 29 × 25 mm (mittig) Wandstärken: 2,5 mm seitlich, 5 mm an den Enden