Drawer Organizer Grid for Mini Toolbox Top Drawer
Created today
Description
Small screws, bits, and sockets slide into one pile in the shallow top drawer of a U.S. General Mini Toolbox. This 3×2 organizer grid drops into that drawer and gives each group its own bin, so you can grab one without dragging the rest along.
- Footprint: 215.5 × 140 × 26 mm, sized for the top drawer with clearance.
- Compartments: six bins, each about 69.7 × 67.6 mm.
- Walls and floor: 1.6 mm walls, 1.2 mm floor.
- Bin floors: 5 mm rounded bottom edges so small parts can be scooped out instead of trapped in square corners.
- Printing: one piece, no separate inserts or assembly.
The grid works as a single tray: print it, drop it in, and lift the whole thing out when you need the drawer back. The rounded floors are part of the print, not loose scoops.
Images
More like this
Explore more in Storage & Organization →
3×2 Drawer Organizer Grid for Mini Toolbox
A six-compartment drawer organizer sized to sit in the bottom drawer of a U.S. General mini toolbox. The 3×2 grid keeps small parts separated, with 1.6 mm outer and internal walls and a 1.2 mm floor. Each bin has a 5 mm concave scoop along the front and back wall, so fingers and small parts slide up the curve instead of catching on a square edge. The overall footprint is 215.5 × 140 × 51 mm. 3×2 grid, six bins 1.6 mm walls and 1.2 mm floor 5 mm finger-scoop fillets front and back in every bin Sized for the bottom drawer of a U.S. General mini toolbox
Two-Piece Rack for 14 Game Tiles
This stand holds fourteen game tiles upright and ready at the table. It is split into two halves that join at the middle with a dovetail, so it breaks down for storage. A low front lip runs along the front of the base, and the fixed back panel leans back 15° so tiles rest in a steady lean against it. The rack is sized for tiles about 17 mm wide, 7 mm deep and 24 mm high, and it has no dividers between tiles. To assemble, drop the tab on the left half down into the socket on the right half from above. The joint sits flush with the tray floor, so the tile slot stays clear. The tab is 3 mm tall, which keeps the halves aligned but is not a strong joint; a dab of glue makes it permanent. Both halves print flat on the plate and need no supports. The dovetail socket is cut to 0.04 mm clearance per side — about the limit for a typical printer, so the halves may not seat by hand. If they bind, sand the tab lightly. Holds 14 tiles sized for 17 × 7 × 24 mm Two halves, about 127 mm and 121 mm long as printed, joined by a drop-in dovetail with 0.04 mm clearance per side Overall length about 242 mm when assembled, leaving roughly 4 mm of slack across 14 tiles 8 mm deep tile slot in front of the back panel, giving about 1 mm of clearance over a 7 mm tile 2 mm front lip, 6 mm high, keeps tiles from sliding forward Fixed back panel about 23 mm tall, leaning back 15° No tile slots or dividers; tiles sit side by side in the tray Both halves print flat without supports
Gridfinity-Schraubenbox 2x1 ohne Label
Gridfinity-Behälter im Format 2x1 Units, 4 Units hoch (28 mm plus 4,4 mm Stapelrand), stapelbar, mit Halfgrid-Boden (4 × 2 Füße im 21-mm-Raster). Vorne läuft eine Rundung mit 18 mm Radius in den Boden aus, damit sich Schrauben und Kleinteile leicht herausschaufeln lassen. Die Vorderseite ist glatt, ohne Label-Mulde. Remix-Ansätze Rundung vorne: Radius 18 mm. Kleiner ergibt eine steilere Rampe, größer eine flachere Schräge mit weniger Restvolumen. Wandstärke und Boden: Wand 2,4 mm, Boden 5,5 mm. Beides lässt sich für leichtere oder robustere Boxen ändern. Label: Die Variante mit Label ergänzt eine 70 × 13 mm große Mulde, 0,8 mm tief, auf der Vorderseite. Alternativ lässt sich ein Schild aufkleben. Höhe: Die Höhe von 28 mm in Vielfachen von 7 mm anpassen, um andere Gridfinity-Höhen zu erhalten. Kombination: Passt auf Gridfinity-Baseplates mit 42-mm-Raster und stapelt mit gleichartigen Boxen. Vor dem Serienausdruck eine einzelne Zelle zur Passprobe drucken.
Screw-Top Storage Jar With Lid
A 60 mm wide, 70 mm tall storage jar with a 50 mm threaded mouth and a matching screw-on lid. It suits spare screws, washers, small hardware or dry spices, and replaces a makeshift jam jar with something sized for the job. The thread is a coarse two-start design with an 8 mm pitch, so the lid goes on in about one turn and comes off just as quickly. The lid has a knurled grip band around its edge for a firm hold, and 0.4 mm of thread clearance to keep the two parts from fusing when printed. The thread fit has not been test-printed, so a small adjustment to clearance may be needed for your printer. Jar: 60 mm diameter, 70 mm tall including the neck Mouth: 50 mm threaded neck Lid: 60 mm diameter, 18 mm tall, knurled grip band Thread: coarse, two-start, 8 mm pitch Walls: 2.5 mm, with a 3 mm floor Printed as two separate pieces, jar and lid
Logitech G PRO X 60 ISO Keycap Organizer
A fully 3D-printable keycap storage organizer for the Logitech G PRO X 60 mechanical keyboard in ISO layout. It keeps the keycap set in keyboard order rather than loose in a bag or tray, with a snap-fit pocket for each keycap and a separate slip-over dust lid. The organizer body and lid print as two pieces; the lid is laid out upside-down beside the body so it prints flat. Fitment Host: Logitech G PRO X 60, ISO version only. The pocket layout follows the 60% ISO rows; it does not fit the ANSI G PRO X 60 layout. Key sizes: 1u, 1.25u, 1.5u, 1.75u, 2u, 2.25u, 2.75u and a 6.25u spacebar pocket. The left Shift pocket is 2.25u. ISO Enter: one L-shaped pocket, 1.5u across the top and 1.25u across the lower step, joined into a single cavity. Retention: each pocket has two thin flexing fingers on the left and right walls, 10 mm wide with a 0.8 mm ramped bump. The fingers are separated by an air gap inside the 3.2 mm wall. Keycaps click past the bumps and pull out by hand. Spares: there is no spare-key row. The organizer holds the keyboard's keycaps in layout order only. Check before printing Pocket pitch is 22.2 mm. A 1u pocket is 19 mm wide, leaving about 0.5 mm per side around an 18 mm keycap base; wider bases will not seat. Pocket depth is 11 mm. Confirm this against your keycaps before printing; the fit has not been checked against physical keycaps. The organizer body measures about 336.2 × 114.2 × 13 mm and the lid 341.2 × 119.2 × 10 mm, with 4 mm rounded corners. Both are over 336 mm long, so a typical 220 mm bed will not fit them; the supplied model is not split into sections.
Hühnerklasse: Schreibtisch-Organizer mit Hühnchen
Ein kleiner Hühnerhof für den Schreibtisch einer Grundschullehrerin: Links sitzt ein rundliches Hühnchen mit dreiteiligem Kamm, Kegelschnabel, Augen, Flügeln und Schwänzchen. In der Mitte steht der Stiftehalter als runder Zylinder mit 64 mm Außendurchmesser; die erhabene Aufschrift „Hühnerklasse“ läuft Buchstabe für Buchstabe um seine Vorderseite, sodass sie auf der Rundung liegt und nicht davor schwebt. Rechts daneben bleibt ein niedrigeres, eckiges Fach für Büroklammern und Radiergummis. Alles steht auf einer schmalen, abgerundeten Bodenplatte von 180 × 72 mm und bildet zusammen ein einziges, zusammenhängendes Stück. Das Hühnchen ist vollplastisch gehalten – Kugelkörper, Kopf, Flügel und Schwanz statt flacher Reliefs. Der Organizer ist als ein Teil ausgelegt, das ohne Stützen auskommen soll; an der Unterseite der kugeligen Körperformen sind leichte Überhänge möglich. Die erhabene Beschriftung auf der runden Vorderseite des Stiftehalters bleibt auch nach dem Druck gut lesbar. Maße, die beim Aufstellen zählen Bodenplatte: 180 × 72 mm, abgerundete Ecken, 4 mm stark Stiftehalter: runder Zylinder, 64 mm Außendurchmesser, 80 mm hoch, oben offen, 4 mm Boden, Innenraum ca. 76 mm tief Ablagefach: eckig, 35 mm hoch, geschlossener Boden Hühnchen: rund 86 mm hoch, mit Kamm und Schnabel als klar abgesetzte Formen Passt zu Stiften, Büroklammern und Radiergummis.