Drehscheibe Neu
Created today
Description
Zwei übereinanderliegende Scheiben (Ø75 mm, je 2 mm dick) mit Randzapfen, die sich gegeneinander drehen lassen. Der Zapfen sitzt an der unteren Scheibe, geht durch die obere und hat oben einen flachen Kopf, der die obere Scheibe hält.
- Untere Scheibe mit Ø30-mm-Mittelloch
- Zapfen Ø6 mm, 30 mm links der Mitte
- Loch in der oberen Scheibe Ø7 mm (0,5 mm Spiel pro Seite)
- Kopf Ø10 mm, 1,5 mm dick, 0,3 mm über der oberen Scheibe
- 0,3 mm Spalt zwischen den Scheiben, druckbar in einem Stück
- Obere Scheibe ist geschlossen, nur Drehbewegung
Images
More like this
Explore more in Desk & Tech →
Fidget Spinner Planetario Ø70 mm
Fidget spinner a ingranaggi planetari stampabile in un solo pezzo (print-in-place), diametro esterno 70 mm, con ingranaggio solare centrale, 5 satelliti e anello esterno dentato internamente. L'anello è alleggerito da 10 fori passanti e non ha coperchi, così gli ingranaggi restano visibili. Diametro esterno: 70 mm, spessore 8 mm Modulo 1,5; solare 15 denti, satelliti 10 denti, corona 35 denti Denti elicoidali a spina di pesce (25°) che trattengono i satelliti senza assi Gioco sui denti: 0,25 mm Fori centrali Ø7 mm (solare) e Ø5 mm (satelliti) per alleggerire Stampa piatta, senza supporti; PLA o PETG
Lazy-Tongs Piano Bottle Caddy
A pantograph-style drink arm in the spirit of a vintage lazy-tongs: a hooked clip straddles the top of a piano's music desk, and a three-unit scissor mechanism unfolds backward to carry a bottle cup. The cup sits inside a wide, rimmed drip tray, so condensation stays off the keys and cabinet. The arm folds flat for storage and stretches out for use. Pivots are print-in-place pins, and the two end joints ride in slots so the arms can open and close. Design notes Cup bore is 76 mm, sized for a standard 33.8 fl oz (1 L) water bottle; cup wall is 85 mm tall. Drip tray is 96 mm across with a 12 mm rim and sits flush with the arm plane. Clip slot fits a music desk about 13 mm thick; adjust the thickness value to suit your piano. Three colored regions: desk clip, scissor arms, cup and tray. Shown in a partly extended pose; the opening angle can be changed to show it folded or fully reached. Best printed as shown, with 0.4 mm clearances at the pivots. Support is only needed under the clip hook. A full bottle is a cantilever load, so keep the arm short for heavier bottles.
Print-in-Place Concentric Rings
A set of five concentric rings designed to print in place as a single piece. Excellent as a clearance test for your printer or just a satisfying desk fidget. Remix Hooks This design is built on a few key parameters that are begging to be tweaked depending on what you want to use it for: Wall Thickness: Currently set to 2mm for a solid feel. Clearance: Set to 0.4mm gap between rings. If your printer is finely tuned, drop this to 0.2mm or 0.3mm for tighter tolerances. Height: Currently 8mm, but you can scale this up on the Z-axis to turn them into nesting tubes. Inner Diameter: Starts exactly at 25mm to fit over standard dowels or large fingers.
Monolith — MagSafe Dock
Monolith is an architectural desk stand built specifically for the Apple MagSafe charger. It's designed to read as a single sweeping piece of tech, dropping the wire invisibly through the core and directly out underneath the base pad. Features Perfect Fit: Toleranced to 56.5mm to lightly grip the standard MagSafe puck. Seamless Route: The cable threads cleanly inside the stem and travels down to the desk surface. Ergonomic Tilt: Features a 50-degree backrest optimized for at-desk use and FaceID unlocking. Vented Spine: Deep architectural slots line the back for a leaner profile.
Vortex Loop 3-Ring Gimbal Fidget
Pocket fidget made of three nested rings, each pivoting inside the next on cone-shaped pins. Printed as one assembly with no hardware, the rings spin on three perpendicular axes. Overall size: about 68 mm across (outer ring) Ring tube: 6 mm diameter, round section Ring gaps: about 5 mm between rings Pivots: conical pins in sockets with 0.45 mm clearance Material: PLA, no electronics or extra parts Print notes: rings stand on edge in the as-built pose, so a brim or light supports under the middle and inner rings may help. Break the pivots free by hand after printing.
110mm Compact D20 Dice Tower
A 110 mm compact dice tower designed to randomize standard 20-sided dice. The one-piece enclosure integrates a catch tray to contain the dice after descent, while the internal structure uses three alternating baffles to ensure unpredictable rolls. Dimensions: 50 mm wide by 110 mm tall, with a 60 mm extended tray. Fitment: Engineered with clearances for standard 20 mm tabletop dice. Baffles: Three internal deflectors pitched at 40 degrees. Printability: Self-supporting internal geometry prints without support material.