Embroidery Hoop Clearance Frame
Created today
Description
A single-piece clearance frame for testing fabric fitment against the dimensions of the Brother SA431 / EF61 small embroidery hoop.
Designed for FDM printing as a rigid, continuous ring, it skips mounting hardware in favour of a plain profile for preliminary dimensional checks.
- Inner clearance: 50 mm × 38 mm
- Overall footprint: 60 mm × 48 mm
- Frame width: 5 mm uniform wall
- Thickness: 4 mm Z-height
Images
More like this
Explore more in Workshop & Tools →
IV Central Line Wrench
Luer lock connections jam at the worst possible moments, and trying to twist a wet, over-tightened collar with gloved fingers is a lost cause. This is a pocket-sized dual-ended wrench designed to grip those lines without crushing them. It slides right over the tubing and engages the radial ridges on the collar so you can break it loose in one turn. Fit & Printing Large End: 10.2mm inner bore with 1.5mm bite notches (clears 6mm tubing). Fits standard IV collars. Small End: 8.0mm inner bore (clears 5mm tubing). Fits tighter hubs. Thickness: 5mm solid body with ergonomic thumb dimples. Print Settings: Print flat on the bed. Needs 3-4 perimeters for structural rigidity so the open ends don't flex under torque. No supports required.
Zauberstab Verschluss 2.0
Zweiteiliger, hohler zylindrischer Testkörper zur Prüfung von FDM-Toleranzen. Beide Teile verfügen über eine geschlossene Außenwand und schließen bündig ab. Feste Abmessungen: Außen 30.8 mm, Innen 21.8 mm Mindestwandstärke: 1.5 mm im kritischen Bereich der Nuten Mechanismus: Bajonettverschluss mit Arretierungsnocke gegen unbeabsichtigtes Öffnen Druckbar: Ohne Stützstrukturen, flach auf dem Druckbett positioniert
Clinical Auto-Retracting Tape Mount
A functional, single-piece, print-in-place wrist mount for an oval retractable tape measure, designed specifically for clinical nerve conduction studies. This iteration adds two key features requested by the clinician: Captive Retention: The top lip now has a deep 2.5mm overhang, completely trapping the tape measure so it cannot fall out during active movement. The side scallops were raised to keep the lip rigid and continuous. Auto-Retract Cantilever: The floor features an integrated, FDM-compliant C-shaped flexure tongue holding a 4.5mm domed pressure pad. When the tape measure is snapped in, this boss continuously depresses the central retract button, allowing the user to simply pull the tape out and let go for immediate automatic retraction. Setup and Usage Snap the 65×59mm tape measure in button-side down. Thread a standard 20mm or 22mm fabric strap through the side loops for a comfortable, non-restrictive fit on the forearm. Prints flat on its base without supports.
DopplerSled — Physics Pendulum Carrier
DopplerSled er en specialdesignet slæde til fysikforsøg med dopplereffekten. Telefonen hviler på den flade ryg og mod bundstoppet, mens elastikker i sidehakkene holder den fastspændt. Konstruktionen giver maksimal plads til telefonens egne højttalere, og topørets to huller sikrer et stabilt pendulsving uden rotation. Design Universelt fit: Ren L-profil uden frontlæbe betyder at alle telefonstykkelser og covers passer. Printbarhed: Designet lægger sig helt fladt på byggepladen og kan printes helt uden supports. Akustik: Stor centerudskæring lader lyden bære bagud. Montering Placer telefonen, sæt to elastikker over skærmen ved sidehakkene, og træk to snore gennem tophullerne til stativet.
Hoof Evener Thumb Ring
A low-profile thumb ring designed to friction-fit onto the center support of a hoof-evener ruler. The ring is split to flex over a variety of thumb sizes while keeping the geometric center locked perfectly inline with the measurement zero-point. Remix Hooks Thumb clearance: Currently set to an inner diameter of 22mm. The 5mm split opening allows for expansion, but the base diameter is the first thing to dial in for a specific hand. Strut channel: The rear mounting slot is sized for a 12.5mm × 4.5mm vertical support. Adjust this block to match the actual sheet metal or printed strut of the evener. Locking hole: A 3.3mm pilot hole runs through the back wall. Drive an M4 set screw or short bolt through it if the friction fit over the strut needs extra bite.
fence conector
A minimalist, heavy-duty H-profile block. Designed with tight inner clearances and thick outer walls, this spacer is ideal for slotting over rails or serving as a sturdy structural bracket. Dimensions Overall Size: 36mm wide × 50mm deep × 40mm high. Inner Channel: 16mm gap width. Wall Thickness: Solid 10mm posts on either side. Print Notes Prints cleanly on its back or base without supports. The 3mm edge rounding improves handling and prevents stress concentrations at the corners.