Fantasy Chess King, Witch, Fire Horse
Created today
Description
Three chunky fantasy chess pieces that tip over easily when the base is narrow: a king, a witch queen and a fire horse, each on a wide 34 mm round base.
Key numbers
- Pieces: king with horned monster face and crowned scepter, witch queen with bent hat and potion bottle, fire horse with flame mane and tail
- Base: 34 mm diameter, 4 mm thick, flat side down
- Height: about 55–65 mm per piece
- Spacing: 45 mm apart in one row, so each can be split off
- Print: no supports needed for most parts; scepter rod and flame spikes are the thinnest features, so print slowly
- Colours: gray bodies with black, red and orange details
Images
More like this
Explore more in Decor & Display →
Helix — Open-Frame Twisted Fin Lamp Shade
Helix is a flared lamp shade with no solid wall. 72 thin fins spiral through a 60° twist as the shade widens from the base to the top, and three low reinforcing rings hold the whole frame together. The result reads like a lantern or woven cage, and the light comes through as spiralling slats of shadow. The fins and rings are matched on purpose: each fin reaches inward only as far as the rings do, so the inner edge stays clean from bottom to top. A small spoked fitter ring at the base seats the shade over a lamp holder. Dimensions Height: 130 mm Base diameter: about 90 mm Top diameter: about 140 mm Twist: 60° over the full height Features 72 twisted, flared fins, 1.2 mm thick Three low-profile rings at the bottom, middle and top, 3.5 mm tall Fin depth matched to the ring depth (about 6.6 mm at the base, scaling with the flare) Spoked fitter ring at the base, 3 mm tall Print notes Print upright with the fitter ring on the plate. Slow speeds help, since the fins are thin. Use a cool LED bulb only. Fit to a specific socket is untested, so check the fitter ring against your holder.
SMG-11 — Red Dot Machine Pistol Replica
SMG-11 is a life-size, non-functional display replica of the compact machine pistol from Rainbow Six Siege, built in the MAC-11 pattern. The magazine is a separate piece that slides out of a real well in the grip, and a rail-mounted red dot sight sits on top. Features Removable magazine with baseplate, feed lips, catch notch and witness holes Grip with mag well, side texturing, mag release button, trigger and trigger guard Boxy receiver with ejection port, side serrations, safety lever and front sling loop Grooved barrel with muzzle ring Top rail with cross slots, front sight with ears and cocking knob Red dot sight with housing, turrets, battery cap, lens and dot Open wire stock Print notes Overall length is about 280 mm with the stock, so it needs a large bed or splitting into sections. Print the magazine separately, baseplate down. The well has about 0.3 mm clearance per side. Wire stock rods may need supports. Display piece only; it has no working mechanism.
Frontlader — Zweiteiliges Retro-Konsolengehäuse
Frontlader ist ein breites, keilförmiges Konsolengehäuse im Stil der klassischen Frontlader-Konsolen, aufgeteilt in Unterteil und Oberteil zum Verschrauben mit M3. Dunkle Einsätze für Cartridge-Abdeckung, Frontblende und Tasten setzen sich vom hellgrauen Gehäuse ab. Features Unterteil mit Boden, Wänden und vier Schraubsäulen Durchgehende 3,4-mm-Löcher von unten bis zur Trennfuge Oberteil mit Schraubdomen und 2,7-mm-Pilotlöchern Zwei USB-A-Öffnungen in der Front Lüftungsschlitze an Seiten und Oberseite Zwei einzeln druckbare Tasten Dimensions 254 × 203 × 76 mm Trennfuge bei Z 30
FLAGE MAROCAINE
A precisely dimensioned 180x120mm base for a Moroccan flag assembly. The model features an accurate 1mm-deep recess carved as five intersecting straight lines, capturing the true geometry of the traditional interlaced pentagram. Through-holes at the five intersecting tips provide exact alignment for a matching drop-in star, while doubling as push-out points if the star needs to be removed after test-fitting. Specifications Dimensions: 180 mm x 120 mm x 3 mm Recess Depth: 1.0 mm (maintains a 2 mm solid floor) Alignment: Five 2.4 mm diameter positioning through-holes Print Settings: Prints flat on its back; no supports required
iPad Picture Frame Adapter Rödlam 21x30
A two-part adapter plate that centers a 5th Generation iPad (9.7") inside an IKEA RÖDALM frame. It acts as a solid backing spacer, locking the tablet into the frame body while providing a cutout exactly the size of the active screen. The split design fits on a standard 220mm print bed and joins with simple flat printed tabs, avoiding overhangs entirely. Remixing and Adjustments Screen Cutout: Currently set to 197 × 148 mm. If you swap to an iPad with a different bezel ratio, you can adjust these dimensions to crop it cleanly. Frame Depth: The total block depth is 30 mm. Thinner frames will require cutting down the outer block height. Cable Routing: A 16 × 25 mm rear channel provides plenty of clearance for bulky aftermarket Lightning cables. Joints: Uses simple 11 × 14 mm rectangular biscuits. You can easily scale these or add more pairs for extra rigidity depending on your printer's tolerances.
HELLO Name Sign, 112 x 36 mm
Desk or shelf name sign with raised bold HELLO lettering on a flat rounded-corner base plate. Letters are set in a heavy sans-serif so strokes stay thick enough to print cleanly. Plate: 112 x 36 x 3 mm, rounded corners Letters: 4 mm raised, Archivo Black, 22 mm cap size Print flat, no supports needed Two colour regions: plate and lettering, suited to a filament change at 3 mm Material: PLA or PETG