fence conector
Created yesterday
Description
A minimalist, heavy-duty H-profile block. Designed with tight inner clearances and thick outer walls, this spacer is ideal for slotting over rails or serving as a sturdy structural bracket.
Dimensions
- Overall Size: 36mm wide × 50mm deep × 40mm high.
- Inner Channel: 16mm gap width.
- Wall Thickness: Solid 10mm posts on either side.
Print Notes
- Prints cleanly on its back or base without supports.
- The 3mm edge rounding improves handling and prevents stress concentrations at the corners.
Photos
Technical views
More like this
Explore more in Workshop & Tools →
Grey I-Shaped Bracket
A custom I-shaped bracket featuring a 36x50x40 mm outer profile and 15.5 mm side cutouts. Designed with rounded edges for a clean finish and smooth handling. Overall Dimensions: 36 mm wide, 50 mm deep, 40 mm tall Cutouts: 15.5 mm high spacing on the sides Features: 3 mm edge rounding Material: Fits standard filaments perfectly
Verbindungsstück l60mm,d60mm
A straight, uniform hollow pipe designed for structural use or fluid routing. The bore is continuous and centered, producing a robust 2 mm wall suitable for standard FDM printing. Outer Diameter: 60 mm Inner Diameter: 56 mm Length: 60 mm Wall Thickness: 2 mm Orient vertically on the build plate to print without supports.
Zauberstab Verschluss 2.0
Zweiteiliger, hohler zylindrischer Testkörper zur Prüfung von FDM-Toleranzen. Beide Teile verfügen über eine geschlossene Außenwand und schließen bündig ab. Feste Abmessungen: Außen 30.8 mm, Innen 21.8 mm Mindestwandstärke: 1.5 mm im kritischen Bereich der Nuten Mechanismus: Bajonettverschluss mit Arretierungsnocke gegen unbeabsichtigtes Öffnen Druckbar: Ohne Stützstrukturen, flach auf dem Druckbett positioniert
IV Central Line Wrench
Luer lock connections jam at the worst possible moments, and trying to twist a wet, over-tightened collar with gloved fingers is a lost cause. This is a pocket-sized dual-ended wrench designed to grip those lines without crushing them. It slides right over the tubing and engages the radial ridges on the collar so you can break it loose in one turn. Fit & Printing Large End: 10.2mm inner bore with 1.5mm bite notches (clears 6mm tubing). Fits standard IV collars. Small End: 8.0mm inner bore (clears 5mm tubing). Fits tighter hubs. Thickness: 5mm solid body with ergonomic thumb dimples. Print Settings: Print flat on the bed. Needs 3-4 perimeters for structural rigidity so the open ends don't flex under torque. No supports required.
O-Ring — Solid Spacer
A heavy-duty cylindrical ring, measuring exactly 115mm across with a 65mm bore. Built straight and solid, ready to act as a substantial standoff, collar, or structural spacer. Dimensions Outer Diameter: 115 mm Inner Diameter: 65 mm Height: 30 mm Wall Thickness: 25 mm
Zauberstab 1.0
Zweiteiliger, hohler zylindrischer Testkörper zur Prüfung von FDM-Toleranzen. Beide Teile verfügen über eine geschlossene Außenwand und schließen bündig ab. Feste Abmessungen: Außen 30.8 mm, Innen 21.8 mm Mindestwandstärke: 1.5 mm im kritischen Bereich der Nuten Mechanismus: Bajonettverschluss mit Arretierungsnocke gegen unbeabsichtigtes Öffnen Druckbar: Ohne Stützstrukturen, flach auf dem Druckbett positioniert