Description
A precisely dimensioned 180x120mm base for a Moroccan flag assembly. The model features an accurate 1mm-deep recess carved as five intersecting straight lines, capturing the true geometry of the traditional interlaced pentagram.
Through-holes at the five intersecting tips provide exact alignment for a matching drop-in star, while doubling as push-out points if the star needs to be removed after test-fitting.
Specifications
- Dimensions: 180 mm x 120 mm x 3 mm
- Recess Depth: 1.0 mm (maintains a 2 mm solid floor)
- Alignment: Five 2.4 mm diameter positioning through-holes
- Print Settings: Prints flat on its back; no supports required
Images
More like this
Explore more in Decor & Display →
Flat-Print A4 Picture Frame
A clean, single-piece A4 picture frame designed to print flat on large beds (like 360x360mm). It prints face-down to ensure a smooth front finish and requires zero supports. Integrated Keyholes: Built-in flush mounts for both portrait and landscape orientation. Drop-in Retainers: Six small twist-clips print alongside the frame in the empty center space. They drop into the pre-drilled holes on the back to lock your paper and cardboard backing firmly in place. Generous Recess: The back channel allows up to 2.5mm of clearance, leaving plenty of room for standard A4 paper paired with a corrugated cardboard or stiff card backing.
Nelore BCS Display Base
What it's for A structured, segmented display base designed to present five cattle models demonstrating Body Condition Scores (BCS). Features an elegant multi-tiered design with distinct angled platforms, giving each figure a dedicated presentation space without structural clutter. Dimensions Overall footprint: 400 mm length x 100 mm width. Total height: 20 mm (10 mm main base, 5 mm middle tier, 5 mm individual platforms). Display pads: 65 mm x 40 mm, offset at a 25-degree angle. Split halves: 200 mm length each, designed to fit cleanly on standard 256x256 mm print beds. Print notes Orientation: Print both base halves flat on their bottoms. Print the pegs horizontally as oriented in the file for maximum shear strength across the layer lines. Clearances: The dowel holes are 8.4 mm with 8.0 mm pegs. This 0.2 mm radial clearance is generous enough for easy assembly straight off a standard FDM printer, but tight enough to hold firmly with CA glue. Supports: None required. All chamfers and geometries are optimized for direct bed printing.
SMG-11 — Red Dot Machine Pistol Replica
SMG-11 is a life-size, non-functional display replica of the compact machine pistol from Rainbow Six Siege, built in the MAC-11 pattern. The magazine is a separate piece that slides out of a real well in the grip, and a rail-mounted red dot sight sits on top. Features Removable magazine with baseplate, feed lips, catch notch and witness holes Grip with mag well, side texturing, mag release button, trigger and trigger guard Boxy receiver with ejection port, side serrations, safety lever and front sling loop Grooved barrel with muzzle ring Top rail with cross slots, front sight with ears and cocking knob Red dot sight with housing, turrets, battery cap, lens and dot Open wire stock Print notes Overall length is about 280 mm with the stock, so it needs a large bed or splitting into sections. Print the magazine separately, baseplate down. The well has about 0.3 mm clearance per side. Wire stock rods may need supports. Display piece only; it has no working mechanism.
iPad Picture Frame Adapter Rödlam 21x30
A two-part adapter plate that centers a 5th Generation iPad (9.7") inside an IKEA RÖDALM frame. It acts as a solid backing spacer, locking the tablet into the frame body while providing a cutout exactly the size of the active screen. The split design fits on a standard 220mm print bed and joins with simple flat printed tabs, avoiding overhangs entirely. Remixing and Adjustments Screen Cutout: Currently set to 197 × 148 mm. If you swap to an iPad with a different bezel ratio, you can adjust these dimensions to crop it cleanly. Frame Depth: The total block depth is 30 mm. Thinner frames will require cutting down the outer block height. Cable Routing: A 16 × 25 mm rear channel provides plenty of clearance for bulky aftermarket Lightning cables. Joints: Uses simple 11 × 14 mm rectangular biscuits. You can easily scale these or add more pairs for extra rigidity depending on your printer's tolerances.
HELLO Name Sign, 112 x 36 mm
Desk or shelf name sign with raised bold HELLO lettering on a flat rounded-corner base plate. Letters are set in a heavy sans-serif so strokes stay thick enough to print cleanly. Plate: 112 x 36 x 3 mm, rounded corners Letters: 4 mm raised, Archivo Black, 22 mm cap size Print flat, no supports needed Two colour regions: plate and lettering, suited to a filament change at 3 mm Material: PLA or PETG
Sprout — Tapered Planter
Introducing Sprout — a classic, no-nonsense tapered planter designed for robust root health. Built with thick walls and a sturdy top rim, it brings a clean, timeless aesthetic to any shelf or window ledge, ensuring your greenery takes center stage. Dimensions Outer Diameter: 100mm (tapering down to 75mm at the base) Overall Height: 95mm Wall Thickness: 2.5mm Features Drainage Array: Features one central 10mm drain and six 8mm radial drain holes to prevent waterlogging. Reinforced Rim: A 5mm chamfered top lip adds structural rigidity while giving you a solid grip when repotting. Print-Ready: Flat base and smooth taper guarantee a flawless print without supports.