Flush Citrus Bow Tie
Created today
Description
A wearable multi-colour bow tie featuring flush-inlaid citrus slices that are trimmed perfectly to the tie's outer edge. The base is 3mm thick, swapping to the fruit colours halfway up for a clean flush surface.
Remix Hooks
- Scale the Slots: The elastic slots are exactly 2.5mm by 15mm. If you're using thicker strapping, dial that square size up before printing.
- Tweak the Layout: The position, size, and rotation of every slice is driven by a central data array, making it simple to pack them tighter or scatter them further.
- Shape the Tie: The bow tie shape is driven by a rough polygon and smoothed via aggressive offset passes; change the offsets if you want a sharper, more geometric profile.
Images
More like this
Explore more in Decor & Display →
Sectioned Amniotic Egg Anatomy Model
A 180 × 130 × 130 mm egg cut in half along its length. The back half holds every anatomical layer nested with about 0.4 mm gaps. The front shell half is a separate lid you lift away to see inside. Each layer prints flat on its cut face. Layers, outside in Eggshell: 2.5 mm, in two halves Outer and inner shell membranes: 1.4 mm each Chorion: 1.4 mm Albumen: fills the space around the yolk and sac, with channels for the chalazae Yolk, r 28 mm, inside a 1.6 mm vitelline membrane Amnion: a 13 mm sphere with a 10.5 mm cavity, opening at the cut face Embryo: curled, with head, tail and two limb buds Allantois: a sac beside the amnion Chalazae: two twisted cords, each about 50 mm long Air cell: an open void at the wide (+X) end, between the shell membranes Remix hooks Layer offsets (0, 2.9, 4.7, 6.5, 8.3 mm): change these to thicken or thin any membrane. Cut plane: moving it off y = 0 gives a wider or narrower window. A quarter-cut is also an easy variant. Air cell: set by the 72 mm start of its void. Move it to resize the cell. Not included: pins, label plates and a reference chart. Small tags or a printed key card would pair well with this model. Scaling: the model scales cleanly for a smaller, faster print.
Zero Talent Motivational Wall Plaque
A minimalist, multi-color printable wall plaque featuring the popular motivational list "Ten Things That Require Zero Talent". Designed strictly to the 180×240mm proportions requested, the plaque is split into distinct printable regions that allow for easy AMS filament mapping in standard slicers like Bambu Studio. Printing Specifications Size: 180 mm × 240 mm × 3.6 mm Layout: Flat backing suitable for mounting tape. Colors: Separated into three distinct mesh regions: a mauve-gray top header block, a charcoal main block, and stark white raised text and dividers. Details: 0.6 mm raised elements optimized for standard 0.4 mm nozzles without needing fine-tuning or supports.
Helix — Open-Frame Twisted Fin Lamp Shade
Helix is a flared lamp shade with no solid wall. 72 thin fins spiral through a 60° twist as the shade widens from the base to the top, and three low reinforcing rings hold the whole frame together. The result reads like a lantern or woven cage, and the light comes through as spiralling slats of shadow. The fins and rings are matched on purpose: each fin reaches inward only as far as the rings do, so the inner edge stays clean from bottom to top. A small spoked fitter ring at the base seats the shade over a lamp holder. Dimensions Height: 130 mm Base diameter: about 90 mm Top diameter: about 140 mm Twist: 60° over the full height Features 72 twisted, flared fins, 1.2 mm thick Three low-profile rings at the bottom, middle and top, 3.5 mm tall Fin depth matched to the ring depth (about 6.6 mm at the base, scaling with the flare) Spoked fitter ring at the base, 3 mm tall Print notes Print upright with the fitter ring on the plate. Slow speeds help, since the fins are thin. Use a cool LED bulb only. Fit to a specific socket is untested, so check the fitter ring against your holder.
Miniature Lifting Trolley Prototype
A demonstration-scale lifting trolley for a mechanical engineering project: rectangular frame, flat platform, four swivel casters, four corner stabilizer legs, a rotating boom base, a bottle jack, a hook with chain, and a push handle. Display model only. The real design targets 900 kg, but this print cannot lift loads. Remix hooks Frame: 80 x 130 x 8 mm. Scale it for a longer platform. Boom: 95 mm at 50 degrees. Change the angle or length to alter reach. Legs: 5 mm rods, 22 mm long. Lengthen them for a higher stance. Pairs with: a small printed crate as a payload.
Miniature Log Cabin for Toy Trains
A small log cabin for model railway layouts and toy train sets. Stacked round logs with overlapping corners form the walls, with a front door, side windows and a gable roof. Footprint about 60 x 45 mm, wall height 32 mm plus roof Door and window openings on the walls Hollow interior with open underside Two colour regions: log walls and roof Print upright on the flat base; the roof overhang is shallow and prints without supports in most cases.
Aerocord — Wire Heart Frame
A smooth, continuous 10mm tubular loop mathematically traced into a classic heart shape, scaled to a full 20cm span. Ideal as a minimalist wall piece, a wreath frame, or a standalone desk feature. Dimensions Width: 200 mm Cord Diameter: 10 mm Overall Profile: Sits flat with a 10 mm Z-height Features Continuous Sweep: A closed tubular loop with no hard joints. Classic Proportions: Driven by standard parametric heart equations for a familiar, balanced shape. Ready to Print: Sits perfectly flat on the bed, requiring zero supports.