Gary Desk Sign
Created 1 months ago
Description
A freestanding desk sign designed to stop wobbling and falling over when the desk is bumped. The custom underline and descender pin hold the piece perfectly horizontal on a flat surface, fighting the usual top-heaviness of 3D-printed text.
Sizing & Details
- Extrusion depth: The letters sit 15mm thick for a sturdy footprint, with the underline and pin set at 12mm deep to offset the profile.
- Full stop: Split into a separate 2mm top cap for a clean multi-color slice.
- Support requirement: Prints flat on its face without supports.
Images
More like this
Explore more in Desk & Tech →
Phone Stand with Cable Channel
A phone stand that holds the phone upright in portrait or landscape, with a cable channel so the charger doesn't pin the phone down or dangle off the edge. Most stands either tip the phone back too far to tap or force the cable to loop around the outside. This one leans the phone at 70° from horizontal and routes the cable up through the stand to the back of the phone. What decides fit and print Lean angle: 70° from horizontal, steep enough to tap the screen and upright enough to watch video. Groove: runs the full 90 mm width, so the phone sits in it in either orientation. It is sized for a phone in a thin case. Cable channel: 12 mm wide, open on the underside of the base. It runs in from the back, then rises through a 12 x 12 mm opening in the groove floor. Overall size: 90 mm wide, about 56 mm deep and 70 mm tall. Printing: the flat base goes down on the bed. The underside channel is a 7 mm-tall tunnel, so print it with bridging on or light supports. No other supports are needed. Material: PLA or PETG both work. Use 3 or more perimeters for a stiffer groove lip.
Organischer Kopfhörerständer in Rosa
Kopfhörerständer mit breitem, abgerundetem Bogen, geschwungenen, sich kreuzenden Streben und einer flachen, wellenförmigen Standfläche. Ein zusammenhängender Körper, flach druckbar, gedacht für pastellrosa PLA. Remix-Ansatz Bogen: Außenradius 65 mm, Strebenbreite 22 mm. Größerer Radius für breitere Kopfbügel. Streben: Vier Kurven, Kontrollpunkte frei verschiebbar für andere Öffnungen. Basis: ca. 224 × 150 mm, 8 mm hoch. Dicker oder mit Gewicht-Einlage für mehr Standsicherheit. Tiefe der Streben: 36 mm, anpassbar. Gesamthöhe ca. 260 mm.
Arcade Console Desk Clock Case
A compact desk-clock enclosure with a gaming-rig attitude: chamfered shoulders, vented flanks and grooved front stripes under the OLED window, like a mini console from a late-night LAN party. Window for a 0.96" OLED on the front Standoffs for an ESP32 WROOM-32 devkit USB slot at the back Four corner screw bosses and a separate screw-on lid Side vent slots for airflow
StudyDock Desktop Phone Stand
What it's for A one-piece desktop phone stand for students, holding a phone at a 65° viewing angle on a desk. Dimensions 65 mm wide, 75 mm deep, 70 mm tall 4 mm flat base, 4–5 mm walls 14 mm deep shelf with a 6 mm front lip Two triangular side supports Remix ideas Widen the shelf for phones with cases. Add a cable slot through the backrest. Lower the backrest angle for typing-height viewing.
Snake Tail Phone Stand
A one-piece orange phone stand with a low front lip, a short flat seat and a backrest leaning up to about 60 mm. A zig-zag snake of humps runs along the back. Remix hooks Lip height: the front stopper is about 5 mm of strip plus the strip's rounded end, roughly 7.5 mm in total. Raise it for a more secure hold, or lower it further to keep captions clear. Seat depth: 12 mm. Deepen it for thick cases, though a steeper backrest helps more. Backrest angle and height: it rises about 18 mm in Y over 55 mm in Z, so it is steep. Both are easy to change. Snake humps: 4 peaks, each about 14 mm high. Add more humps, or raise or lower the peaks. Width: 70 mm, with a 5 mm strip thickness. Pairs well with a non-slip pad on the seat.
Fidget Spinner Planetario Ø70 mm
Fidget spinner a ingranaggi planetari stampabile in un solo pezzo (print-in-place), diametro esterno 70 mm, con ingranaggio solare centrale, 5 satelliti e anello esterno dentato internamente. L'anello è alleggerito da 10 fori passanti e non ha coperchi, così gli ingranaggi restano visibili. Diametro esterno: 70 mm, spessore 8 mm Modulo 1,5; solare 15 denti, satelliti 10 denti, corona 35 denti Denti elicoidali a spina di pesce (25°) che trattengono i satelliti senza assi Gioco sui denti: 0,25 mm Fori centrali Ø7 mm (solare) e Ø5 mm (satelliti) per alleggerire Stampa piatta, senza supporti; PLA o PETG