GridLock — Small Drop-In Bins
Created 1 months ago
Description
A set of three drop-in utility bins tailored to fit the smallest full compartment (the 3.5" × 5.1" back-right section) of the open frame system.
They share a common footprint but offer different internal layouts for organizing small hardware or desk sundries.
Variants Included
- Open Bin: A single large cavity for maximum storage.
- Split Bin: Divided neatly in half for sorting smaller items.
- Coin Scoop: Features a smoothly swept floor across its length, allowing you to easily slide out coins or tiny parts without them getting trapped in a corner.
Dimensions
- Outer Footprint: 88.5 mm × 130.5 mm
- Height: 38 mm (designed to sit flush just below a 40 mm frame)
- Clearance: Sized 0.4 mm smaller than the slot for a comfortable drop-in fit
Images
More like this
Explore more in Storage & Organization →
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
3×2 Fächergitter 40×40 mm, 60 mm hoch
Fächergitter mit sechs durchgehenden Schächten (3 nebeneinander, 2 hintereinander), oben und unten offen. Gedacht als Sortier- oder Einsatzraster für Teile, die in einen 40 × 40 mm Schacht passen. Maße Fach innen: 40 × 40 mm Höhe: 60 mm Wände: 2 mm, auch zwischen den Fächern Außenmaß: 128 × 86 × 60 mm Steg: umlaufender Rand bei 20 mm Höhe, 2 mm dick, 5 mm breit; Öffnung dort 30 × 30 mm Vor dem Drucken prüfen Der Steg ist eine Annahme: ein umlaufender Rand in jedem Fach. Ein Teil, das durch das Fach muss, braucht Platz im 30 × 30 mm Durchlass. Passt nicht Gegenstände über 30 mm Breite passen nicht durch die Stegöffnung.
Two-Piece Gridfinity Caliper Box
A 6 x 3 unit Gridfinity caliper box split at the middle into two halves, each about 126 x 126 x 25.4 mm, so each fits a 150 mm print bed. Two dovetail keys join the halves. The stepped pocket holds a 9.25 in caliper: a 15.9 mm body slot and a 78 x 97.5 mm head recess, both 12.7 mm deep. The stacking lip and finger scoops are kept. Remix hooks Split position: the cut is at X = 0, on a Gridfinity cell boundary. Moving it in whole 42 mm steps keeps the cells intact. Dovetail size: 8 mm at the root, 13 mm at the tip, 16 mm tall, at Y = ±35. The socket has 0.25 mm clearance. Loosen or tighten it to suit your printer. Joint type: swap the dovetails for round pins or add glue grooves. Pairs with: other Gridfinity bins on a 42 mm baseplate.
Tabletop Wildlife Alert, 100 mm Diamond Sign
Modular tabletop wildlife-warning prototype printed as separate parts that bolt together: base, three pole sections, four brackets, electronics enclosure with lid, PIR sensor housing with rain hood and lid, amber light housing with lid, and a diamond sign reading WILDLIFE CROSSING with no graphic. The stack runs bottom to top: electronics enclosure, PIR sensor facing forward, two amber LED openings, then the sign. Each housing screws to its own bracket, and each bracket clamps onto the pole with one cross-screw. Dimensions (mm, outside) Electronics enclosure: 70 × 60 × 50, interior about 65 × 57 × 45, with lid PIR housing: 60 × 40 × 35, 23 mm lens opening, rain hood, with lid Light housing: 70 × 35 × 30, two 8 mm LED openings, with lid Sign: diamond 100 point to point, 3 mm thick Base: 100 × 84 × 6 Pole: three sections, 20 × 20 × 58 Overall height: about 224 To confirm before printing Controller board size (a full Uno will not fit the interior) PIR lens diameter and LED diameter (23 mm and 8 mm are placeholders) Printer build area Electronics are untested